Kenwood PS-60 Manual De Instrucciones

DC POWER SUPPLY
PS-60
INSTRUCTION MANUAL
We are grateful you purchased this KENWOOD DC Power Supply.
SUPPLIED ACCESSORIES
AC Power Cable (2 m/ 6.5 feet) ................................................. 1
Instruction Manual ....................................................................... 1
Warranty Card ............................................................................. 1
PRECAUTIONS
• Do not expose the unit to rain or moisture to avoid the risk of
fi re or electric shock.
• Do not touch the power plug when your hands are wet to avoid
risk of electric shock.
• Do not remove the case. Accidentally touching an internal part
may result in serious electric shock.
• If a metal object such as a hair pin or a needle comes into
contact with the power socket on the rear panel, a dangerous
electric shock may occur.
• Keep children away from the unit, to avoid unnecessary risk of
harm to the child.
• Always remove the plug from an AC outlet by pulling on the
plug, not the cable.
• Position the AC cable so it will not be stepped on, tripped over,
nor subjected to damage.
• Plug the AC cable only into a grounded AC outlet.
• Unravel the AC power cord before use.
• In case of an abnormality in the equipment, ensure the
equipment is plugged into an outlet that can be easily accessed,
so that the plug may be disconnected from the outlet.
• To avoid equipment damage, do not connect to a transceiver
that operates on a voltage other than 13.8 V DC or exceeds the
current rating.
• Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
• Do not place the unit in excessively dusty and/or humid areas,
nor on unstable surfaces.
• Do not block the power supply air vent. Do not cover the unit.
To maintain good ventilation, place the unit at least 10 cm (4
inches) away from the wall.
• Do not use solvents such as benzene or paint thinner to clean
the unit. Use a silicone or a clean, dry cloth.
• Do not install this equipment in a constricted location, such as a
book case.
• If you detect an abnormal odor or smoke coming from the unit,
turn OFF the power immediately and disconnect the power
cord. Contact your KENWOOD service center or dealer.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or
modifi cations to this equipment may cause harmful interference unless
the modifi cations are expressly approved by the party responsible/
JVC KENWOOD. The user could lose the authority to operate this
equipment if an unauthorized change or modifi cation is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to an outlet on a circuit diff erent from that to
which the receiver is connected.
•
Consult the dealer for technical assistance.
ORIENTATION
Front Panel
Indicator (Red)
DC POWER SUPPLY PS-60
(Output monitor)
Power switch
Power switch
Press this switch to turn the power ON and OFF.
Rear Panel
Cooling Fan
• This power supply is for use with a transceiver . Do not use the
power supply with other products.
• Before connecting the DC power cable to the transceiver
terminal, or removing it from the terminal, turn the power supply
power OFF.
• For connection instructions, refer to the transceiver instruction
manual.
• When placing the power supply beside the transceiver, adjust
the power supply bail to an appropriate angle. You can further
use commercially available rubber pads/ feet to adjust the angle
to match that of the transceiver.
SPECIFICATIONS
Power requirements .............. 100 V ~ 240 V AC ±10%, 50/60 Hz
Output voltage ...................................................... 13.8 V DC ±5%
Rated output current ........................................................... 22.5 A
Operating temperature range . –10°C ~ + 50°C (–22°F ~ +130°F)
Dimensions (W x H x D) <without projections>
.................173.5 x 95.5 x 204.3 mm (6.83 x 3.76 x 8.04 in)
Dimensions (W x H x D) <with projections>
...............175.9 x 108.6 x 228.1 mm (6.93 x 4.28 x 8.98 in)
Weight ........................................................ approx. 2.5 kg (5.5 lb)
AC Plug .............................................................. 3 pin (Grounded)
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF UNINSULATED"DANGEROUS
VOLTAGE"WITHIN THE PRODUCT'S ENCLOSURE THAT MAY
BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF
ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE
IS INTENDED TO ALERT THE USER TO THE PRESENCE OF
IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE
APPLIANCE.
The equipment is designed for connection to an IT power distribution system.
B62-2296-20 (K) (1/3)
Bail
AC Power
Cable
"+" Terminal
"−" Terminal
© 2015