Blaupunkt ISD-SD1 Manual Del Usuario página 8

MINI SMOKE ALARM DEVICE
Model number: ISD-SD1
Ref: 03318220
Thank you for purchasing our innovative
smoke alarm device
Diagram 1
• POWER: built-in DC3V(CR123A) Lithium
battery (battery not replaceable)
• OPERATION CURRENT: <8uA (standby),
<70mA (alarm)
• ALARM VOLUME: >85dB(A) at 3 meters.
• ALARM SENSITIVITY: 0.096-0.148dB/m
• SILENCE TIME: approx. 10 minutes
• SMOKE ALARM DEVICE SOUND PATTERN:
BI 0.5s - pause 0.5s – BI 0.5s – pause 0.5s –
BI 0.5s – pause 1.5s, with the red LED flash,
repeat this alarm pattern.
• COMPLY WITH STANDARD: EN14604:2005+
AC:2008
Description:
The unit is a photoelectric smoke alarm
device. With the photoelectric technology, it
is more sensitive to detecting slow smolder
fires which general thick, black smoke, a
little heat and may smolder for hours before
bursting into flames. The smoke alarm
device does not contain the radioactive
material. It is harmless to the environment.
The Mini smoke alarm device should be in-
stalled in every room (except the bathroom
and kitchen), and every other area of the
home, making sure the people in the home
will be able to hear and respond to the
alarm sound. For minimum protection, you
should fit one device respectively for the
hallways, living room, and bedrooms. Each
unit shall be placed in the middle of the
ceiling of each room to protect.
Typical single storey dwelling with recom-
mended:
Install a smoke alarm device on the ceiling
inside each bedroom and in the hallway
outside each separate sleeping area. If a
bedroom area hallway is more than 30 feet
long, install a smoke alarm device at each
end. If there is a basement: install a smoke
8
7
0333-CPR-292150-1
EN14604:2005+AC:2008
DoP:ISD-SD1-001
G217046
alarm device on the basement ceiling at the
bottom of the stairwell.
Typical multi-storey dwelling with recom-
mended protection.
Install a smoke alarm device on the ceiling
inside each bedroom and in the hallway
outside each separate sleeping area. If a
bedroom area hallway is more than 30 feet
long, install a smoke alarm device at each
end install a smoke alarm device at the top
of a first – to- second floor stairwell.
Important Safety Information:
1: The test button accurately tests smoke
alarm device functions. Do not use any
other test method. Test smoke alarm
device weekly to ensure proper operation.
2: If you're sure it isn't a really alarm, open
windows or fan the air around smoke
alarm device for silence it
3: Observe and follow all local and
national electrical and building codes for
installation.
4: This smoke alarm device is designed to
be used inside a single family housing or
apartment only. In multifamily buildings,
each individual living unit should have
its own smoke alarm devices. Do not
install in non-residential buildings. This
smoke alarm device is not a substitute
for a home security alarm system and it
cannot be connected to any Blaupunkt
Alarm System.
5: Install a smoke alarm device in every room
and on every level of the home. Smoke
may not reach the smoke alarm device for
many reasons. For example, if a fire starts
in a remote part of the home, on another
level, in a chimney, wall, roof, or on the
other side of a closed door, smoke may
not reach the smoke alarm device in time
to alert household members. A smoke
alarm device will not promptly detect a
fire except in the area or room in which
it is installed.
6: Smoke alarm device may not alert every
household member every time. The alarm
horn is loud in order to alert individuals
to a potential danger. However, there
may be some circumstances where a
household member may not hear the
alarm (i.e. outdoor or indoor noise, sound
sleepers, drug or alcohol usage, the hard
of hearing, etc.). If you suspect that this
smoke alarm device may not alert a
household member, install and maintain
specialty smoke alarm devices. Household