Air Compressor Safety - GMC GAC1500 Manual Del Usario

• Hold the tool correctly; be ready to counteract normal or sudden movements and have
both hands available
• Maintain a balanced body position and secure footing
• Release the start-and-stop device in the case of an interruption of the energy supply
• Use only lubricants recommended by the manufacturer
• Personal protective safety glasses should be used; suitable gloves and protective clothing
are recommended
• Avoid direct contact with moving parts in order to prevent pinching or cutting of hands or
other body parts
• Wear suitable gloves to protect hands
• There is a risk of electrostatic discharge if used on plastic and other non-conductive
GB
materials
Repetitive Motions Hazards
• When using this tool to perform work-related activities, the operator can experience
discomfort in the hands, arms, shoulders, neck or other parts of the body
• While using this tool, the operator should adopt a comfortable posture whilst maintaining
secure footing and avoiding awkward or off-balance postures. The operator should
change posture during extended tasks; this can help avoid discomfort and fatigue
• If the operator experiences symptoms such as persistent or recurring discomfort, pain,
throbbing, aching, tingling, numbness, burning sensations or stiffness, these warning
signs should not be ignored. The operator should inform the employer and consult a
qualified health professional
Accessory Hazards
• Disconnect the tool from the energy supply before fitting or changing the inserted tool or
accessory
• Avoid direct contact with the inserted tool during and after use, as it can be hot or sharp
• Use only sizes and types of accessories and consumables that are recommended by the
manufacturer of this tool; do not use other types or sizes of accessories or consumables
Workplace Hazards
• Slips, trips and falls are major causes of workplace injury. Be aware of slippery surfaces
caused by use of the tool and also of trip hazards caused by the air line or hydraulic hose
• This tool is not intended for use in potentially explosive atmospheres and is not insulated
against contact with electric power
Dust and Fume Hazards
• Dust and fumes generated when using this tool can cause ill health (for example
cancer, birth defects, asthma and/or dermatitis); risk assessment and implementation of
appropriate controls for these hazards are essential
• Risk assessment should include dust created by the use of the tool and the potential for
disturbing existing dust
• Direct the exhaust so as to minimise disturbance of dust in a dust-filled environment
• Where dust or fumes are created, the priority should be to control them at the point of
emission
• Select, maintain and replace the consumable/inserted tool as recommended in the
instruction handbook, to prevent an unnecessary increase in dust or fumes
• Use respiratory protection in accordance with employer's instructions and as required by
occupational health and safety regulations
Noise Hazards
• Exposure to high noise levels can cause permanent, disabling hearing loss and other
problems, such as tinnitus (ringing, buzzing, whistling or humming in the ears). Therefore,
risk assessment and implementation of appropriate controls for these hazards are
essential
• Appropriate controls to reduce the risk can include actions such as damping materials to
prevent workpieces from 'ringing'
• Use hearing protection in accordance with employer's instructions and as required by
occupational health and safety regulations
• Operate and maintain this tool as recommended in the instruction handbook, to prevent
an unnecessary increase in the noise level
• Select, maintain and replace the consumable/inserted tool as recommended in the
instruction handbook, to prevent an unnecessary increase in noise
• If the tool has a silencer, always ensure it is in place and in good working order when the
tool is being operated
Vibration Hazards
• This information shall draw attention to vibration hazards that have not been eliminated by
design and construction and remain as residual vibration risks. It shall enable employers
to identify the circumstances in which the operator is likely to be at risk from vibration
exposure If the vibration-emission value obtained using ISO 28927-3 does not adequately
represent the vibration emission in the intended uses (and foreseeable misuses) of the
machine, additional information and/or warnings shall be supplied to enable the risks
arising from vibration to be assessed and managed.
• Exposure to vibration can cause disabling damage to the nerves and blood supply of the
hands and arms
• Wear warm clothing when working in cold conditions and keep your hands warm and dry
• If you experience numbness, tingling, pain or whitening of the skin in your fingers or
hands, stop using the machine, inform your employer and consult a physician
• Operate and maintain the sander or polisher as recommended in the instruction
handbook, to prevent an unnecessary increase in vibration levels
• Hold the tool with a light but safe grip, taking account of the required hand reaction forces,
because the risk from vibration is generally greater when the grip force is higher

Air Compressor Safety

When using machinery there are certain precautions that need to be taken in order to
promote safe operation. Always apply caution and respect to the machinery in use; if the
following safety precautions are ignored then damage or harm may be subjected to the
operator, property or bystander. It is in the interest of the user to read and pay attention to the
following guidelines.
WARNING: This air compressor does not produce breathable air. Ingesting compressed air is
dangerous and can cause harm.
WARNING: Hot surfaces are present. DO NOT touch the motor, cylinder, heads and tubes as
harm may occur from burning.
WARNING: DO NOT use in potentially explosive atmospheres. Ensure that the atmosphere is
free from combustible gases and high concentrations of fine dust.
a) NEVER use compressed air for an unintended use. Compressed air has the potential to
cause harm. Avoid directing compressed air towards animals or persons, and NEVER
release compressed air towards the skin.
b) Ensure the work area is debris-free and dry. Untidy workspaces raise the potential for
injury.
c) Compressor should be assembled correctly. Using a compressor with guards, covers
and components removed is dangerous and may compromise the compressor's ability to
perform.
d) DO NOT modify the compressor. Modifications to the compressor can be dangerous.
Unapproved modifications may not only hinder the compressor's ability to perform,
but may result in harm being caused to the operator. Repairs should be carried out by
qualified personnel only, using only manufacturer verified components.
e) Safety valves should not be modified or tampered with. Doing so can cause harm to the
operator and damage the air compressor. The maximum pressure is predetermined by
the manufacturer and should not be adjusted.
8