Niko 16-661-01 Manual Del Usuario página 13

16-661-01 / 16-660-01 / 16-660-02
For a description of the total system, we refer to the catalogue and manual or to our website www.niko.be.
1. LEGAL WARNINGS
- Read the complete manual before attempting installation and activating the system.
- The installation has to be carried out by a registered installer and in compliance with the statutory regulations.
- This user manual has to be handed over to the user. It has to be included in the electrical installation file and has to be passed on to any new owners.
Additional copies are available on the Niko website or via the support service.
- During installation, the following has to be taken into account (not limited to list below):
- The statutory laws, standards and regulations;
- The state of the art technique at the moment of installation;
- This user manual, which must be read within the scope of each specific installation, only states general regulations;
- The rules of proper workmanship
- In case of questions, you can consult Niko's support service or contact a registered control organisation.
Support Belgium:
+32 3 760 14 82
website : http://www.niko.be
e-mail: support@niko.be
In case of a defect, you can return your product to a registered Niko wholesaler, together with a clear description of your complaint (Conditions of use,
stated defect...).
2. DESCRIPTION
The 16-661-01 is a video internal unit and is part of the range Access Control Design. This appliance can display a color image of your visitor while you
are talking to him/her. The 16-661-01 video internal unit is suitable for surface mounting on a wall (as a standard). It can also be used as a freestanding
appliance. You can adjust the angle of inclination by means of the supplied base (16-660-01). The video internal unit can also be partially flush mounted in
the wall by means of a special mounting box (16-660-02). You can also use this appliance as an ordinary analog telephone. In this case, provide 24V DC for
this appliance. The video internal unit 16-661-01 is powered via the UTP cable of the system. The internal unit is provided with a flat color LCD display.
3. INSTALLATION
3.1. Check whether you have the following components at your disposal:
- video internal unit 16-661-01
- UTP cable, CAT.5E (from the video splitter or switcher to the video internal unit) with RJ45 connectors at both sides.
The UTP cable connects the 16-661-01 to the video splitter or switcher.
This UTP cable (CAT.5E) contains the cores for connection to the power supply, the analog telephone line, the video signal and a bus.
1 + Vsup
2 - Gnd
3 Bus H
4 TEL tip
5 TEL ring
6 Bus L
7 VIDEO +
8 VIDEO -
3.2. Installation as surface mounting appliance
Mount the video internal unit 16-661-01 on the wall as shown in fig.1. Provide a standard flush mounting box at the indicated place.
3.3. Installation as flush mounting appliance
Mount the video internal unit 16-661-01 as shown in fig. 2, 3 and 4. Provide a standard flush mounting box behind the flush mounting frame (16-660-02)
at the indicated place. Then mount the flush mounting frame on the flush mounting box. The opening in the wall must have the following dimensions: L221
x W188 x D21mm.
Attention: Take into account the depth of the flush mounting frame when placing the standard flush mounting box.
3.4. Installation as a freestanding appliance on a base (16-660-01)
Mount the base as in fig. 5. Choose the fixing points that enable to look at the display perpendicularly.
EN
Support Slovakia:
+421 263 825 155
e-mail: niko@niko.sk
color code UTP cable:
1. orange-white
2. orange
3. green-white
4. blue
5. blue-white
6. green
7. brown-white
8. brown
1. Vsup (+)
2. Ground (-)
3. bus H
4. telephony (tip)
5. telephony (ring)
6. bus L
7. video+
8. video-
13