Matco Tools BG612 Manual Del Usario

WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.
INTENDED USE OF THE TOOL
This bench grinder is designed to sharpen drill bits, blades, chisels,
flat screwdrivers, etc. Do not use this tool outside of the designed
intent. Never modify the tool for any other purpose or use.
WARNING
Caution: To help prevent personal injury
• Normal use of this product is likely to expose the user to dust and/or
microscopic particles containing chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
Always wear appropriate safety equipment and clothing when using
this product. Study, understand and follow all instructions provided
with this product. Failure to read and follow all warnings and
operating instructions may result in damages and serious injury or
death.
• Always wear ANSI approved goggles when using this product.
(Users and Bystanders).
• Never use this tool for any application other than for which it was
designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool, modification of
the tool, or use of the tool with accessories not designed for it could
result in serious injury or death.
• Always select the correct accessories of the correct size and design
for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and adequately
equipped area.
• Do not begin repairs without assurance that vehicle is in secure
position, and will not move during repair.
IMPORTANT
Read these instructions carefully before installing, operating, servicing
or repairing this tool. Keep these instructions in a safe accessible place.
6" 1/2 HORSE POWER BENCH GRINDER
Product Type:
MODEL:
BG612
6" 1/2 HORSE POWER BENCH GRINDER
DO NOT DISCARD – GIVE TO USER
MADE IN CHINA
Page 1
1 YEAR LIMITED WARRANTY
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the
date of purchase.
The manufacturer reserves the right to determine whether the part or
parts failed because of defective material, workmanship or other
causes. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
The manufacturer, at its discretion, will repair or replace products
covered under this warranty free of charge. Repairs or replacements
of products covered under this warranty are warranted for the
remainder of the original warranty period.
The manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by unauthor-
ized service representatives voids this warranty. The rights under this
warranty are limited to the original user and may not be transferred to
subsequent owners.
This warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular
purpose. Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitations may
not apply to you.
UNPACKING
When unpacking, check the parts diagram and part number listing on
page 4 to make sure all parts are included. If any parts are missing or
damaged, please call your dstributor.
PRODUCT INFORMATION:
• Quiet and vibration free high torque induction motor
• Heavy duty construction for durability for most grinding applications
• Heavy duty grinding wheel covers
• Two 6" grinding wheels included (#9580GW36 – 36 Grit and
#9580GW60 – 60 Grit)
• Front mount easy access on/off switch for safety and convenience
• Adjustable tool rests and upper tongue guards are included for safe
operation
• Adjustable eye protection shields included for maximum eye and
face protection
SPECIFICATIONS:
• 1/2 HP single phase electric motor with class E insulation
• Voltage/frequency: 115V-60Hz
• Amps AC: 3.5A
• Maximum no-load speed: 3,550rpm
• Electric power supply cord with 3 prong ground plug; 18-3 SJT x 6'
long (UL listed)
• Grinding wheel dimensions: 6" O.D. x ¾" W. x ½" A.H.