Technical Parameters; Other Information - Elko CRM-81J Manual Del Usario

Technical parameters

Function:
Supply terminals:
Voltage range: AC/DC12-240V
(AC 50-60 Hz)
Power input max. AC 0.7-3 VA /
(apparent / loss): DC 0.5-1.7 W
Max. dissipated power
(Un + terminals):
Supply voltage tolerance:
Supply indication:
Time ranges:
Time settings:
Time deviation:
Repeat accuracy:
Temperature coeffi cient:
Output
Changeover contacts:
SPDT (AgNi / Silver Alloy)
Rated current:
Breaking capacity: 4000 VA / AC1, 384 W / DC
Inrush current:
Switching voltage:
Output indication:
Mechanical life:
Electrical life (AC1):
Control
Consumption of input: AC0.025-0.2VA/
DC 0.1-0.7W
Load between S-A2:
Control. terminals:
Glow tubes connection:
Max. amount of glow
lamps connected to
controlling input:
Impulse length:
Reset time:

Other information

Operating temperature:
Storage temperature:
Electrical strength:
Operating position:
Mounting / DIN rail:
Protection degree:
Overvoltage cathegory:
Pollution degree:
2
Max. cable size (mm ):
Dimensions:
Weight:
Standards:
* measured with glow lamp 0.68 mA / 230 V AC
CRM-81J CRM-83J
ZR - delay ON, ZN - delay OFF, BL - cycler 1:1
A1 - A2
AC 230 V/ AC/DC12-240V
50-60 Hz (AC 50-60 Hz)
AC 12 VA / AC 0.7-3 VA /
1.3 W DC 0.5-1.7 W
4 W 4.5 W
-15%; +10%
green LED
0.1 s - 10 h (in 6 ranges)
potentiometer
5 % - mechanical setting
0.2 % - set value stability
0.01% / °C, at =20 °C
1x changeover / 3x changeover /
SPDT (AgNi / Silver Alloy)
16 A / AC 1 8 A / AC1
2000 VA / AC1, 192 W / DC
30 A / < 3 s 10 A / < 3 s
250 V AC / 24 V DC
red LED
3x10 7
5
0.7x10
AC0.025-0.2VA/
AC 0.53 VA DC 0.1-0.7W
No Yes No
A1-S
No Yes No
x max. 10 pcs* x
min. 25 ms / max. unlimited
max. 150 ms
-20 °C to +55 °C (-4 °F to 131 °F)
-30 °C to +70 °C (-22 °F to 158 °F)
4 kV (supply - output)
any
DIN rail EN 60715
IP40 from front panel / IP20 terminals
III.
2
solid wire max. 1x 2.5 or 2x 1.5 /
with sleeve max. 1x 2.5 (AWG 12)
90 x 17.6 x 64 mm (3.5˝ x 0.7˝ x 2.5˝)
60 g (2.1 oz.) 85 g (3 oz.)
EN 61812-1, EN 61010-1
Functions
AC 230 V/
50-60 Hz
AC 12 VA /
1.9 W
Note: the function ZR and ZN is controlled by supply voltage and control input ie. Once
phase failure is detected and supply voltage is re applied. The relay automatically makes
one cycle.
Warning
Device is constructed for connection forf 1-phase main 230 V or AC 12-240 V and must
be installed according to norms valid in the state of application. Connection according
AC 0.53 VA
to the details in this direction. Installation, connection, setting and servicing should be
installed by qualifi ed electrician staff only, who has learnt these instruction and functions
Yes
of the device. This device contains protection against overvoltage peaks and disturbancies
in supply. For correct function of the protection of this device there must be suitable
Yes
protections of higher degree (A, B, C) installed in front of them. According to standards
elimination of disturbancies must be ensured. Before installation the main switch must
be in position "OFF" and the device should be de-energized. Don´t install the device to
sources of excessive electro-magnetic interference. By correct installation ensure ideal
max. 10 pcs*
air circulation so in case of permanent operation and higher ambient temperature the
maximal operating temperature of the device is not exceeded. For installation and
setting use screw-driver cca 2 mm. The device is fully-electronic - installation should be
carried out according to this fact. Non-problematic function depends also on the way of
transportation, storing and handling. In case of any signs of destruction, deformation, non-
function or missing part, don´t install and claim at your seller it is possible to dismount the
device after its lifetime, recycle, or store in protective dump.
2 / 2
ZR - Delay ON
U
S
t t
ZN - Delay OFF
U
S
t t t
BL - Cycler 1:1
U
S
t t t t t t t