Installation Instructions; Getting Started; Mounting Considerations - Garmin GC 100 Instrucciones De Instalación

Ocultar thumbs Ver también para GC 100:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 6
GC

Installation Instructions

Getting Started

See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.

Mounting Considerations

• You must mount the camera in a location where it is not
submerged.
• You should mount the camera within 76 m (250 ft.) of a
chartplotter. The range depends on your installation location
and obstacles between the camera and the chartplotter. If the
camera is out of range of the chartplotter due to obstacles or
distance, you must reposition the camera.
• You should test the camera in your desired location before
you permanently mount the camera.
• You should mount the camera so that the cable can be
connected easily.
• You should mount the camera in a location where it cannot
be damaged by docks, pilings, or other pieces of equipment.
• You should mount the camera so it does not present a
hazard in doorways or walkways.
• You should mount the camera in a location where you can
remove the camera.
Mounting the Camera
1
1
Using a 3.2 mm (
/
in.) drill bit, drill a pilot hole.
8
NOTE: If you are mounting the camera onto fiberglass, it is
recommended to use a countersink bit to drill a clearance
counterbore through the top gelcoat layer only, but no
deeper. This will help to avoid cracking the gelcoat layer
when the screws are tightened.
2
Using the included screw, fasten the camera mount to the
mounting surface.
3
Insert the camera
into the housing
4
Close the front of the housing.
5
Tighten the tamper-proof side screws using the included tool.
6
Connect the power cable.
Pairing the GC
100 Camera with a Garmin
Chartplotter
Before you can connect a wireless device to the chartplotter
wireless network, you must configure the chartplotter wireless
network.
1
With the camera within an unobstructed 76 m (250 ft.) of the
chartplotter, quickly press
2
100
WARNING
.
three times.
2
On the chartplotter, select Settings > Communications >
Wireless Devices > Garmin Camera > Start.
3
Follow the on-screen instructions.
Turning the Camera Off
Hold
for 3 seconds.
NOTE: If you hold
resets.
Specifications
Water rating*
Operating temperature range
Charging temperature range
Storage temperature range
Input voltage
Compass-safe distance
Wireless frequency and protocol 2.4 GHz Wi‑Fi
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to
/waterrating.
GC 100 Blink Codes
After the camera is installed and paired with the chartplotter, the
camera turns on when the chartplotter is turned on. The color
and blink sequence of the status LED on the camera indicates
its operational status.
LED
LED State
Color
Green
Three blinks
Red
Three blinks
Blue
One blink per second for up to
two minutes, or until the
camera connects to a
chartplotter
Amber
One blink per second until the
camera powers down or the
battery is charged
®
for more than 10 seconds, the camera
IEC 60529 IPX6/IPX7
From -20 to 60°C (from -4 to 140°F)
From 0 to 45°C (from 32 to 113°F)
From -40 to 85°C (from -40 to 185°F)
From 3.9 V to 6.2 V, 2 A
10 cm (4 in.)
®
@ 17 dBm nominal
www.garmin.com
Status
The camera is turning on.
The camera is turning off.
The camera is attempting to
connect to a chartplotter
using Wi‑Fi.
The camera battery is not
charged sufficiently to
stream video.
Installation Instructions

Publicidad

Tabla de contenido
loading

Tabla de contenido