Masterlock SAFESPACE 5423D Manual De Usario

g. 1
Recode Tool
Outil de reprogrammation
Herramienta de recodi cación
RECODE TOOL
g. 2
g. 2c
Weather
Protective
Cover
g. 4
Protection
contre les
intempéries
Cubierta
protectora
contra el clima
#5423D
Wall Mount Push Button Lock Box
Coffret verrouillé à boutons á montage mural
Caja de seguridad con botón de contacto para montar en la pared
g. 1a
Operating Instructions:
"OPEN" Button
Bouton "OPEN"
(OUVRIR)
To open lock box for first time
Botón "OPEN"
(ABRIR)
use (fig. 1):
"CLEAR" (C) Button
1. Press down "CLEAR" (C) button ( g. 1b).
Bouton "CLEAR" 2. Press down "OPEN" button ( g. 1a).
(EFFACER)
3. Guide compartment door down to
Botón "CLEAR"
fully open.
(BORRAR)
g. 1b
To set a new combination (fig. 2):
1. Open lock box and locate the yellow
Recode Tool.
2. With compartment door open, locate the 12
yellow plastic slotted buttons behind the door
(numbered from 0 to 9 and symbols # and *).
All arrows on buttons should be set to the
"SET OFF" position ( g. 2b).
Set On
3. Using the yellow Recode Tool or a small athead
Activé
screwdriver, PUSH and TURN the desired
SET
Activado
ON
number/symbol buttons 180° (1/2 turn) ( g. 2c)
g. 2a
to the "SET ON"position ( g. 2a).
SET IMPORTANT:
Set Off
OFF
Désactivé * COMBINATION CAN BE 1-12 CHARACTERS
LONG BUT CANNOT USE THE SAME
Desactivado
CHARACTER MORE THAN ONCE.
g. 2b
** BUTTON IS PROPERLY SET WHEN IT
POPS UP. IT SHOULD NOT REMAIN
PUSHED IN.
180º
g. 3
g. 5
Removable
Key Hook
Crochet
amovible
pour les clés
Gancho
de llave
extraíble
g. 3a
g. 3b
4. The lock is now set to your
new combination.
5. Save your combination in a safe place
such as masterlockvault.com or record
it below.
To close and lock box (fig. 3):
1. Press down "CLEAR" (C) button ( g. 3a).
2. Enter the combination.
3. Press down and hold "OPEN"
button ( g. 3b).
4. Close compartment door.
To open lock box with set
combination (fig. 3):
1. Press down "CLEAR" (C) button ( g. 3a).
2. Enter the combination.
3. Press down "OPEN" button ( g. 3b).
4. Guide compartment door down
to fully open.
To hang wall mount model:
You will need: pencil or marker, Phillips
head screwdriver, level, drill, and drill bit.
For certain surfaces (masonry) anchors
and a hammer are recommended.
1. Open the compartment door.
(see instructions above)
2. Position the lock on the desired surface.
3. Use level to verify the lock is vertical.
4. Mark the position of the screw holes
on the surface.
5. Remove lock.
6. Drill holes.
7. If necessary, use hammer to place anchors.
8. Position lock.
9. Insert and tighten screws.
10. Close compartment door.
11. Scramble the combination dials to lock the
door and conceal your combination (A).
Notes:
1. Always keep weather cover closed to
withstand extreme weather ( g. 4).
2. Use ANTI-JAM hook to hang keys and
prevent loose keys from jamming
the door closed ( g. 5).
Key Storage
Compartment
Compartiment
de rangement
des clés
Compartimiento
de almacenamiento
de llaves