Fein GRI GIXS Instrucciones De Uso página 7

Original Instructions for undercarriage.
Symbols, abbreviations and terms used.
The symbols used in this Instruction Manual and possibly
on the undercarriage, serve to draw your attention to
possible hazards when working with the undercarriage.
Symbol Term, meaning
➤
Action
Read documentation
General mandatory sign
Danger warning
Screw
Screw, metric
Anchor
European conformity symbol
For your safety.
Do not use this undercarriage before you
have thoroughly read and completely
understood this Instruction Manual, includ-
ing the figures, specifications and safety reg-
ulations.
Read and observe the Instruction Manual of
the machine which is to be mounted on this
undercarriage.
Please also observe the relevant national industrial safety
regulations (e. g. in Germany: BGV A2, BGR 500).
Non-observance of the safety instructions can lead to an
electric shock, fire and/or severe injuries.
These operating instructions should be kept for later use
and enclosed with the power tool, should it be passed on
or sold.
Make sure that the undercarriage stands securely and has
a level setup position. Fasten the undercarriage to the
ground. If the undercarriage tips over during operation,
serious injuries can result.
Use appropriate fastening material when mounting the
machine to the undercarriage. When mounted incor-
rectly, the machine can come loose from the undercar-
riage and cause serious accidents.
GIXBE:
The mains plug of the extraction system may be mounted
only by a qualified electrician. The protective conductor
in the mains socket outlet must be connected with the
protective earthing of the mains supply.
Pull out the mains plug for maintenance and repair! Switch-
ing on the extraction system unintentionally can lead to
an electric shock.
Have the electrical safety of the extraction system checked
regularly in accordance with statutory regulations. For sys-
tems that have not been checked, there may be danger of
electrical shock!
At a glance.
1 On/Off switch
2 Support
3 Hose clamp
4 Extraction hose
5 Lock
6 Door
7 Frame
8 Filter insert (fine filter)
9 Filter insert (coarse filter)
10 Collection receptacle
11 Latch
12 Fastening screws
Intended use of the machine.
The undercarriage is intended for stationary mounting
of GRIT GI100, GIE, GXE belt grinders.
Mounting instructions (Figures A + B).
Fasten the undercarriage to the ground with suita-
ble anchor/screw connections. The fastening must
be suitable to withstand the forces occurring dur-
ing working.
➤ Place the machine to be mounted onto the sup-
port (2).
Due to the danger of accidents, this work must be
carried out by persons that are physically capable
of lifting the high weight of the machine.
Fasten the machine onto the support with suitable
screws (12).
➤ Connect the extraction hose (4) to the machine's
connection sleeve for dust extraction and tighten the
hose clamp (3).
Electrical connection (GIXBE).
Observe mains voltage: The mains voltage and the fre-
quency of the power source must agree with the data on
the type plate of the machine.
Before starting operation for the first time, check the
rotation direction of the motor. The rotation direction
may be changed only by a qualified electrician.
Plug the mains plug of the extraction system into the
intended socket outlet on the machine.
Operating instructions.
Switching ON and OFF (GIXBE)
The extraction system is automatically switched on or off
via the On/Off switch (1).
Emptying the collection receptacle/
Replacing the filter insert
(GIXBE – Figure D).
➤ Unlock the two locks (5) and open the door (6).
➤ Loosen the latch (11) and completely pull out the fil-
ter unit. Take both filter inserts (8)/(9) out of the
frame (7).
➤ Clean the filter inserts with compressed air and
empty the collection receptacle (10).
en
7