Traxxas Velineon 3500 Manual De Instrucciones

Velineon 3500 Brushless Motor Instructions
Thank you for purchasing the Velineon
3500 sensorless brushless motor.
The Velineon 3500 brushless motor is
precision-matched for use in 1/10th scale
Traxxas models, delivering the perfect
balance of brutal horsepower and long
run times. Smooth-running performance
is built in with ultra high-temperature sintered Neodymium magnets,
high-speed ball bearings, and a precision balanced rotor. The solder
tabs for the motor wires are protected from damage by a unique
composite end cap.
The Velineon 3500 can be used with many after-market brushless
electronic speed controls, but is designed to work with the Traxxas
VXL-3s Electronic Speed Control for optimal speed and efficiency.
The key to the Velineon's extreme power output is total system
optimization. Each component is carefully engineered to work with
the other system components to eliminate restriction and allow
maximum power flow.
Velineon 3500 Specifications:
Type ..........................................................................................Sensorless brushless
RPM/volt ............................................................................................. 3500 (10-turn)
Magnet type ....................Ultra High-Temperature Sintered Neodymium
Connection type ............................................. TRX 3.5mm bullet connectors
Wire size ............................................................................12-gauge Maxx® Cable
Current Ratings ............................................. 65A constant; 100A peak/burst
Max RPM ............................................................................................................. 50,000
Diameter .......................................................................... 36mm (1.42") (540 size)
Length................................................................................................. 55mm (2.165")
Weight ...................................................................................................262g (9.24oz)
Installation
(Traxxas Rustler shown, Bandit and Stampede are similar.)
1. Mount the Velineon Motor to the gearbox
using 3x8mm screws and tighten finger
tight (white arrows).
2. Mount the motor pinion to the motor shaft,
make sure to tighten set screw against the
flat portion of the shaft.
3. Set the gear mesh by running a narrow strip
of notebook paper between the pinion and
spur gears. Loosen the motor screws and
slide the motor and pinion gear into the spur
gear. Retighten the motor screws and then
remove the strip of paper.
Traxxas, 1100 Klein Road, Plano, TX 75074, Phone: 972-265-8000, Fax: 972-265-8011, e-mail: support@Traxxas.com
Wiring Diagram
™
Follow the wiring diagram below for installing the Velineon 3500 with
a VXL-3s Electronic Speed Control. For other speed controls, consult
the manufacturer's instructions.
Exploded View
3351
5x11x5BB
3342 Bullet connectors, male, 3.5mm (3) / heat shrink
3354 Motor cover, endbell (Velineon 3500)
3352 Rebuild kit, Velineon 3500 (includes 5x11x5mm ball bearings
3353 Rotor, Velineon 3500
3347 Screws, 2.5x5mm button-head machine (hex drive) (6)
3931 Screws, 3x8mm flat-head machine (hex drive) (6)
3355 VXL-3s Electronic Speed Control (brushless) (fwd/rev/brake)
3343 Wire, 12-gauge, silicone (Maxx Cable) (650mm or 26 inches)
If you are planning to operate the motor at the
higher limits of its capabilities, cut ventilation
holes into your model's Lexan
temperatures will extend the lives of the batteries
and motors. An on-board temperature gauge
such as the Traxxas part #4091 can aid you in monitoring your motor
Strip of
Paper
temperature. Generally, try to keep your motor below 200° F.
If you have questions or need technical assistance, call Traxxas at
1-888-TRAXXAS
Motor
Screws
TR A X XA S .c om
3347
2.5x5BCS
3352
3351
3347
2.5x5BCS
(2), 2.5x5mm BCS (2), front and rear bushings)
® body. Monitoring
(1-888-872-9927) (U.S. residents only)
Covers Part #3351
3353
5x11x5BB
3352
3351
3354
Rev 120813 KC1682-R00