Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Frame rail
Tow hook
Hitch Shown In Proper Position
Equipment Required: Lubricant or Soapy water
Fastener Kit: 24846F
Wrenches: 17mm, 11/16"
Bulkhead
Note: Fasteners typical
both sides
1
Qty. (1)
Carriage bolt 7/16-14 X 2.00 GR5
2
Qty. (1)
Spacer
3
Qty. (1)
Conical washer 7/16"
1.
Lower exhaust system at the rear rubber isolator leaving the rubber isolator in place on the vehicle. Spraying a lubricant on the metal hanger
rod and the rubber isolator helps removal
2.
Insert the carriage bolt and spacer through the tow hook.
3.
3
Lift hitch into position, passengers side first. Place crosstube over top of tail pipe. Rotate into position on the outside of the frame rail. It may
Lift hit h i t
iti
be necessary to pull the fascia gently out of the way.
4.
Raise the drivers side of the hitch up so it's on the outside of the frame rails and in front of bulkhead (rotate as needed). Once again, it may be
necessary to pull the fascia gently out of the way.
5.
Raise hitch into position behind end panel and fasten to tow hook with conical washer and hex nut. Hand tighten.
6.
Attached remaining fasteners as shown.
7.
Push hitch toward the rear of the vehicle.
8.
Tighten all fasteners to the required torque specification.
9.
Reattach rubber muffler hanger.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2009, 2011 Cequent Performance Products
Installation Instructions
Kia Forte
Fascia
Drawbar Kit:
Drawbar Kit:
3954
Drawbar must be used in the
Rise position only.
5 6
Rearward
id fi t Pl
t b
Tighten all M10 CL 8.8 fasteners with torque wrench to 42 Lb.-Ft. (57 N*M)
Tighten all 7/16-14 GR5 fasteners with torque wrench to 50 Lb.-Ft. (68 N*M)
Do Not Exceed Lower of Towing Vehicle
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Existing weld nuts
Both sides.
Bulkhead cut
away to show
installation
1
1
2
3
Tail pipe
Tail pipe
4
4
4
Qty. (1)
Hex nut 7/16-14
5
Qty. (4)
Hex bolt M10 X 1.25 X 30mm CL8.8
6
Qty. (4)
Conical washer 3/8"
t
f t il i
R t t i t
Sheet 1 of 3
24846N
Part Numbers:
24846
60262
77219
24862
Manufacturer's Rating or
Wiring Access Location: xxx
iti
th
t id
f th f
6-1-11
Form F206 Rev A 5605
U-HAUL
Frame rail
il It
Rev. B
Publicidad
Manuales relacionados para Cequent 24846
Resumen de contenidos para Cequent 24846
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2009, 2011 Cequent Performance Products Sheet 1 of 3 24846N 6-1-11 Rev.
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2009, 2011 Cequent Performance Products Feuille 2 de 3...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2009, 2011 Cequent Performance Products Hoja 3 de 3 24846N 6-1-11 Rev.