Chamberlain Group K3 Manual Del Usuario

CLICKER MODEL K3
WIRELESS KEYPAD
FEATURES
Congratulations! The Clicker Model K3 you have purchased is one
of the most unique keypad transmitters available. It is compatible
with most garage door opener systems manufactured by
Chamberlain ® , Genie ® , Lift-Master
Moore-O-Matic ® , Multi-Code
Please note that the K3 is not compatible with rotating code systems
such as Intellicode™ or Security+™, developed by several of these
manufacturers since 1996.
The Clicker K3 can be programmed to operate one or two garage
door openers, including different brands. When used with two doors,
each door is programmed separately, with separate Personal
Identification Numbers (PINs).
In addition, the K3 must be programmed to your system's security
code. If your system uses code switches, you must match the
existing code. If your system does not use code switches but does
have a smart button, you may enter any random 9 digit code into
the K3, then program your system's receiver to accept this code. All
programming is done through the keypad.
When properly programmed, the K3 will open your garage door
when your PIN, plus any additional number, is pressed. The keypad
remains active for approximately 30 seconds after the last button is
pushed. During this interval you may stop or reverse a moving door
by pushing any numbered key.
If you press an incorrect number, wait 30 seconds and start over.
We suggest you first read through the instructions in their entirety,
then return to Part 1. Follow instructions carefully.
Do not install the unit until programming is completed and tested
from the intended location.
PART 1 – IDENTIFYING YOUR EXISTING BRAND AND CODE
Step 1: Place an X in Table 1 below next to the brand of your
opener. If you are programming your K3 for more than one door
opener, place an X next to the brand you will program first.
___1 Linear, Moore-O-Matic (8 code switches)
___2 Stanley (10 code switches)
___3 Multi-Code (10 code switches)
___4 Sears, Chamberlain, Lift-Master, Master Mechanic,
Wayne Dalton (9 code switches or none; only these brands
may have a smart button)
___5 Genie (9 code switches)
___6 Genie (12 code switches)
Step 2: Determine whether your system uses code switches.
Depending on your brand, you may have 8, 9, 10 or 12. They are
usually located on the opener receiver panel (perhaps under the
lamp cover). The receiver is normally attached to the garage door
opener, or mounted on a wall and wired to the opener. Your existing
remote will have matching code switches inside the case. The
illustration shows a receiver panel and remote with 9 code switches.
Receiver Panel
1 2
1 2 3 4 5 6 7 8 9
+
0
–
Code switches
(white squares indicate position)
® , Linear ® , Master Mechanic
® , Sears ® , Stanley ® , and Wayne Dalton
Table 1
Remote Code Switches
3
• If your system has code switches you must program the K3 to
match the existing code. Proceed to Table 2 or 3, depending on
your brand.
• If your Chamberlain, Lift-Master, Master Mechanic, Sears, or
® , Wayne Dalton receiver does not have code switches, choose
® . any random 9 digit code to program the K3. Use Table 2 and enter
a setting of 1, 2, or 3 for each column. Fill only 1 box per column,
and ignore the table instructions pertaining to code switches. Then
proceed to PART 2 – PROGRAMMING PROCEDURES.
Chamberlain, Lift-Master, Master Mechanic,
1
+
0
–
Examine the code switches on your receiver. This table is 9 columns
across, one for each code switch. Place a "1" in each box that
corresponds with a switch in "+" position. Place a "2" in each box
that corresponds with a switch in "0" position. Place a "3" in each
box that corresponds with a switch in "–" position. Fill only 1 box
per column.
+
0
–
Example: (white squares indicate switch position)
+
0
– 3
Genie, Linear, Moore-O-Matic, Multi-Code, Stanley
1
ON/UP
OFF/DN
Examine the code switches on your receiver or remote. It will have
either 8, 9, 10, or 12 code switches. Place a "1" in each box that
corresponds with a switch in the "on" or "up" position. Place a "2"
in each box that corresponds with a switch in the "off" or "down"
position. Fill only 1 box per column, and only as many columns as
you have code switches. See example below.
NOTE: Some Stanley and Multi-Code units label their code switches
open and close. For Clicker coding purposes,
Close = on, Open = off .
Example of a Stanley with 10 code switches:
CLOSE
OPEN
Step 3: Verify the code numbers you entered in the table to be sure
they match your system's code. Then proceed to PART 2 –
PROGRAMMING PROCEDURES.
For use with Garage Door Openers
Table 2
Sears, or Wayne Dalton
2 3 4 5 6
1 1
2
3 3
Table 3
2 3 4 5 6 7
1 1 1 1 1
2 2
7 8 9
2 2 2
8 9 10 11 12
2 2 2