Publicidad
Idiomas disponibles
Idiomas disponibles
M54504 - EXP. CARD Ethernet & μSD
This is a descriptive manual of the procedure to insert and
configure the inputs/outputs expansion card (relay) of the
CVMk2.
You can download the complete manual in digital format
from www.circutor.com
Before any maintenance, modification to the
connections, repair, etc., the equipment must
be disconnected from the supply and the
measure connections. If wrong operation is
suspected the equipment must remain out of service. The
equipment is designed to changed quickly in the event
of any breakdown.
1. CARD INSTALLATION
Disconnect from supply and measure the device.
Remove the screw and the cover
Insert the card in the guides.
Press the card carefully.
Put the cover and the screw.
2. CARD CONFIGURATION
When we have introduced the card, we have to configure it.
Select
MENU
from the upper line of the display and confirm
SET
with
to unfold the window.
SETUP
SET
Select
and confirm with
move in the upper menu with the arrows since
SET
and select it with
key.
CARD 1
CARD 2
We have 3 options (
,
to select according the position which we have introduced
the card. In the picture is position 1, then we will select
CARD 1
.
NOTE: If select you select a position where is no card, will
NO CARD
appear the message
.
When we have selected the card we have to confirm with
SET
the
key and will enter in the configuration.
To erase the registry files or do a memory format, we have
menu
setup
to unfold the window
, select
SET
key.
The keys of this screen are:
esc
: Go back, window without saving changes.
ok
: Leave the editing window saving the changes.
It creates a single file of events *. EVQ which holds
all voltage events. The files *. STD, are generated
automatically every day.
In format screen, where we can see the following settings.
The memory card has to be FAT16 and maximum
capacity of 2 Gb.
Not insert FAT32 and HCSD formats.
Clear STD
•
Clear evq
•
Format
•
: Do a memory format.
extract
•
3. COMMUNICATIONS
The ethernet and memory card for CVMk2, is designed
specifically to communicate in an ethernet network.
ETHERNET network optimize the IT structure and facilitate
the installation.
3.1. IP SETTING
You can use the Power Studio SCADA (you can download
from www.circutor.com), or by ARP comands.
As example if you want to configure the IP address
172.16.14.254 and the MAC address of the card is 00-20-
4A-8D-66-66.
a) Once that is done, enter the following command to
assign the IP address to the expansion card connection.
b) Now, execute a telnet to port 1. The connection attempt
will always fail, but the CVMk2 will change its IP to the one
previously assigned.
c) Finally, execute a telnet to port 9999 and configure all
the required parameters. Then, it is possible to begin
configuration of the expansion card's Ethernet converter.
It is very important to save the changes before exiting
the configuration menu. Example:
key. Now, we have to
EXP.CARD
CARD 3
or
). We have
in the system, enter the configuration menu, verify the
modifications and exit the menu after saving changes.
Accordingly, the new IP will be saved in the analyzer.
and confirm with
M54504 - Expansion card Ethernet and μSD -
A T E N T I O N : W h e n y o u i n s t a l l a n
m i c r o S D c a r d i n t h e C V M k 2 , i t ' l l b e
formatedautomatically. Don't insert memory
cards with documents that you want to
conserve.
: Erase the last record file.
: Erase the last voltage event detected.
: Stops the communications between device
and memory microSD.
ATENCIÓN: Before to extract the microSD
memory from the device, we have to
stop the communications between device
and microSD card. If don't srops the
communications, the microSD memory card
could be damaged.
c:\ arp -s 172.16.14.254 00-20-4A-8D-66-66
c:\ telnet 172.16.14.254 1
c:\ telnet 172.16.14.254 9999
WARNING: The IP assigned to the CVMk2
with the arp commands is temporary and
the system will recover its original IP when it
loses the power supply. To save the new IP
The connection to the master system, ethernet cabling is
done through four twisted pairs (shielded). Connect at one
end of the card and the other end electronics network (hub
or switch) to the corporate network.
In the case of wanting to make a direct connection to a
computer or device with ethernet input, ethernet cable wi-
res must have a special provision for such communication
4. PARAMETRES
To see the parameters of the microSD memory card, you
have to unfold the window menu and select exp.card.
Select card 1, card 2 or card 3 depending on the position
of the card and will see the parameters:
MEM.size
•
: microSD Capacity in Mb
recorded
•
: Recorded days since last memory format.
events
•
: Voltage events detected since last memory
format
•
free
: % of free memory
•
status
: Indicates the status of the microSD:
a)
SD.OK
: it is correct
b)
No SD
: No microSD detected
c)
WR PROTE
: The microSD has the wirte
protection enable
d)
SD error
: format microSD must done.
5. VARIABLES SELECTION
The card is programmed to record 234 predefined
variables.
In the event that the user needs to modify the selection of
variables, you must use the Power Studio software found
on the web CIRCUTOR, www.circutor.com
After communicating with the computer using the software,
you have access to the driver of the team and therefore
access to the configuration of the card
The user must select the expansion card to be enabled the
following option:
A window will be opened in which displays all the variables
the user can select to register.
6. ICONS
Correct status of microSD memory.
Incorrect status of microSD memory.
microSD card extraction enable.
7. TECHNICAL ASSISTANCE SERVICE
In case of failure or any operational queries, please contact
the technical service of CIRCUTOR, SA.
TECNICAL ASSISTANCE SERVICE (TAS):
(+34) 93 745 29 00
CIRCUTOR, SA. – Aftersales service.
Vial Sant Jordi s/n
08232 Viladecavalls, Barcelona.
Tel.: (+34) 93 745 29 00
Fax: (+34) 93 745 29 14
e-mail: sat@circutor.es
M98209201-20-15A
CVM k 2
.
Publicidad
