Cambro Camshelving CSHDTK10 Instrucciones De Ensamblaje

Camshelving high Density storage system
®
assembly instructions, Product line & general Usage guide
Parts CheCklist
4.5' (1,38 m) Track Rail
5' (1,53 m) Track Rail
6' (1,83 m) Track Rail
Track Rail Joiner
Track Rail Stationary End Plate
Pan Head Screw
Star Washer
Stainless Steel Leveling Foot
Track Rail Stationary Plate Cap
½" (1,3 cm) Hex Nut
Total Pieces
Parts DesCriPtion
Track Rail 4.5' (1,38 m), Pan Head Screw
5' (1,53 m), 6' (1,83 m)
Track Rail Joiner Star Washer
Track Rail ⁄ " (1,3 cm
1
2
Stationary End Plate Hex Nut
Stainless Steel Track Rail
Leveling Foot Stationary Plate Cap
tools required: Phillips Head Screwdriver,
Crescent Wrench, Rubber Mallet
All specs are subject to change without prior notice.
CshDtk10 CshDtk12 CshDtk145
10' (3,05 m) 12' (3,66 m) 14.5' (4,42 m)
Track Kit Track Kit Track Kit
– – 2
4 – 4
– 4 –
2 2 4
4 4 4
16 16 24
16 16 24
8 8 8
4 4 4
4 4 4
58 58 78
high Density Camshelving
storage system
track kits
CSHDTK10 10' (3,05 m) Track Kit for
3 Mobile Units
CSHDTK12 12' (3,66 m) Track Kit for
4 Mobile Units
CSHDTK145 14.5' (4,42 m) Track Kit for
5 Mobile Units
NOTE: ALL Camshelving Units MUST BE 24"
(61 cm) wide only to provide stability. Unit
length may be 36" (91 cm), 42" (107 cm)
or 48" (122 cm) maximum. Select 64" (163
cm) or 72" (183 cm) high Stationary Starter
Units and 67" (170 cm) or 75" (191 cm) high
Mobile Starter Units.
NOTICE: Follow instructions included with
Camshelving Starter Units to build Stationary
and High Density Mobile Starter Units. Use a
Rubber Mallet ONLY to secure Traverses and
Casters onto Camshelving Units. Do NOT use
hard plastic or metal mallets, as they may
cause product damage.
2009 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, CA 92647-2056, U.S.A.
telephone 714 848 1555 toll Free 800 854 7631 Customer service hot line 800 833 3003 Printed in USA
The High Density Camshelving Storage System utilizes all available
space by eliminating aisles. Increases storage capacity by 30% - 40%.
High Density Camshelving is easy to order and assemble. Camshelving
Stationary Units act as the system anchor. High Density Mobile Units
with exclusive High Density Casters and Track Kits complete the system.
high Density Camshelving storage system assembly instructions
®
1. Before you begin to assemble, please refer to the parts checklist to identify and count all of
the parts. If anything is missing, please contact your Cambro Sales Representative, or Cambro
Customer Service at 1-800-833-3003 or 1-714-848-1555 to request missing parts.
2. Lay out sections of track rail end to end with the groove side up, to form two tracks of equal
length.
3. Secure Track Rails together using Track
Rail Joiners. Place a Track Rail Joiner down
into the groove and line it up with the screw
holes in the Track Rails. Secure 4 each Pan
Head Screws and Star Washers using a
Phillips Head Screwdriver. Repeat for 2
(See Fig. 1)
4. Attach one Track Rail Stationary End Plate,
at each end of run of track. Place each
Track Rail Stationary End Plate down into
the groove, and line it up with the screw
holes in the Track Rails. Secure 2 each
Pan Head Screws and Star Washers using
a Phillips Head Screwdriver. Repeat for 2
set. (See Fig. 2)
5. Flip Track Rails over so raised Caster Rail Guide is facing upwards. Place the tracks parallel,
the proper distance apart, and in the intended location.
6. Assemble two each Camshelving Stationary Starter Units per instructions included with each
unit. Carefully lay each unit on its side and unscrew and remove the plastic leveling feet.
Fig. 1
set.
nd
Fig. 2
This Side Up
nd
1