Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
DESCRIPTION
D
escription of the TEKNA HF GTWIN monitor.
Hands-free monitor for the Gtwin system with button and coded panels.
k
a
l
m
b
n
f
c
g
o
p
h
d
q
i
k
j
e
r
a.
4.3" TFT colour screen
b.
Communication with hearing aids. Set the
hearing aid switch to position T.
c.
Call volume control: maximum, minimum
and no volume (night mode).
j.
d.
Function/programming buttons.
e.
Microphone.
f.
Brightness control.
g.
k.
Colour control.
h.
Monitor status LED:
l.
-
In call: LED illuminated green.
-
In communication: LED blinking green.
-
Night mode: LED blinking red.
m.
-
In call (night mode): LED illuminated
n.
yellow.
o.
-
In communication (night mode): LED
p.
blinking yellow/red.
q.
i.
Advanced programming LED:
-
In programming: LED blinking yellow.
-
Doctor mode: LED blinking green.
-
State of the open door on the main panel:
r.
s.
LED illuminated red. (see the TGtwin
System Manual, p. 10)
Continued
D
escription of the connection terminals.
CN4 connection terminals:
LINE
LINE
CP
IN
OUT
LINE IN:
Communication bus input to monitor (non-polarised).
LINE OUT:
Communication bus output to additional monitor/telephone
(non-polarised).
CP:
Door bell button input.
_
CN5 connection terminals:
S+ S
PANIC
S+ :
Output (positive) to auxiliary call repeater SAV-GTWIN.
S :
Output (negative) to auxiliary call repeater SAV-GTWIN.
PANIC:
Input for panic button. (Sends a panic signal to guard unit).
DESCRIPTION
1
F
unction buttons.
Start/stop communication button.
With the monitor in standby: One short 1-second press activates the
monitor in function mode (for 5 seconds).
During a communication process: it activates the talk/listen function, press
to talk. (See the TTEKNA HF GTWIN manual, p. 6 and 7, for how to
establish communication and enable this function, respectively).
No function.
During a call, communication or auto-spy process: it enables the
secondary door release to be activated: one press will activate the door
release for 1 second.
SW1 SW2
With the monitor in function mode: it enables a call to be made to the guard unit.
1 2 3 4 5 6 7 8 9 10
1 2
CN3
J2
CN4
With the monitor in function mode: it activates the intercom between 2
devices in the same apartment or in different apartments (this feature must
CN5
be pre-programmed, see the TTEKNA HF GTWIN manual, pp. 13-16).
Note: Activation of the
function.
s
With the monitor in standby mode: it enables programming mode to be
-
State of the door on the slave
entered or exited by pressing and holding for 5 seconds, a number of
door panel:
short audible tones will indicate that the monitor is in programming mode
LED blinking red. (See the TGtwin
and the programming LED will blink slowly (yellow) or a number of long
System Manual, p. 10).
audible tones will indicate that the monitor has saved and left
Indicator LED:
programming mode, and the programming LED will turn off.
-
Standby: Off.
With the monitor in standby mode: it enables the image from the door
-
Call: LED illuminated green.
panel configured as main to be viewed (if the channel is busy, a
-
Communication: LED
number of short audible tones on the monitor will indicate so); if butto
illuminated green.
is pressed, it enables audio and video communication with the
Connector fixings.
door panel to be established.
J2 jumper (end of line) or EL-566
During a call process: it enables the slave monitors (in the same
IN-OUT unit connector (see the
apartment) to capture the image of the door panel, with the image on the
TTekna HF Gtwin manual).
monitor that was displaying it disappearing.
SW2 configuration switch.
Con el monitor en modo función: activa la intercomunicación entre 2 equipos
SW1 configuration switches.
de la misma vivienda o de distinta vivienda (debe programarse previamente
CN3 connector (no function).
esta funcionalidad, ver manual "TTEKNA HF GTWIN" pág. 13 a 16).
CN4 connection terminals.
No function.
CN5 connection terminals.
During call reception and communication processes, it enables the main
Only by authorised personnel:
lock release to be activated.
M
onitor microphone volume control.
OPERATION
Monitor speaker volume control.
-
Call reception: During call reception, the image will appear on the master
monitor and status LED
monitors will illuminate (green). If the call is not answered within 60 seconds,
the indicator LED and status LED
turn off. LED
-
To establish communication, press button
blink (green), LED on the door panel will then illuminate and LED
door panel will turn off.
the hearing aid is 1 -
quality during communication with the door panel.
aid switch to the T position, making conversation possible (inductive loop).
-
Guaranteed communication time is 90 seconds (configurable); after 90
seconds of guaranteed communication time, the channel will become free.
-
To end communication, press button
status LED
free.
-
To open the main or secondary door, press the corresponding door release
button
activate the lock release for 1 second (configurable main door) and, with the
opening of the main door, LED
function disables the
'intercom'
'call to guard unit'
and the indicator LED on the master and slave
on the master and slave monitor(s) will
on the door panel will turn off and the channel will become free.
on the monitor, status LED
Communication with hearing aids
: Make sure that
0 15
cm away from the monitor to ensure maximum audio
Remember:
, and the monitor's indicator LED and
and door panel LED will turn off and the channel will become
/
during the call or communication processes: one press will
will also illuminate for 1 second.
INSTALLATION
2
I
nstallation of the terminal.
Avoid dusty or smoky environments or locations near sources of heat.
The monitor can be fixed to an electrical embedding box or directly to
the wall.
Important: For further information, see the TTekna HF
Location
1.60m
Surface
ADVANCED PROGRAMMING
Advanced programming of the functions of the Tekna HF Gtwin monitor:
Advanced programming enables the monitor's default settings to be changed:
With the monitor in standby: Press button
seconds to access
tones will confirm this and the monitor's programming LED
will blink (yellow) slowly, indicating that button
released.
Then adjust the settings as required:
-
Changing the door panel ringtone melody:
The monitor enables selection of the ringtone (5 different tones).
Select the ringtone melody: Press button
is heard 'carousel mode.'
-
Changing the ringtone melody from the apartment front door:
The monitor enables selection of the ringtone from the apartment front door (5
different tones).
Select the ringtone melody from the apartment front door: Press
will
button
until the desired melody is heard 'carousel mode.'
on the
-
Activating/deactivating the doctor mode function: Doctor mode not activated
(default setting).
Set the hearing
The 'doctor mode' function enables the main lock release to be activated
automatically 3 seconds after making a call from the door panel without having to
establish communication or press door release button
seconds and the channel becomes free. (Only the master monitor should be
configured with 'doctor mode').
To activate doctor mode: Press button
indicate that the function is activated; if it is pressed again, an audible
tone will indicate that the function will change its status to deactivated and
so on. The monitor's programming LED will blink (green) slowly when the
monitor exits programming mode and is in standby.
Gtwin manual (code 50120254).
Remember to remove the protective
covering from the front of the monitor once
installation is complete.
Embedding box
Screws supplied with the
embedding box.
4 30
x
for more than 5
'programming mode,'
3 short audible
can be
until the desired melody
. The call ends after 15
once, an audible tone will
Continued overleaf
3
Publicidad
Tabla de contenido
