Product Familiarisation - Silverline 828919 Manual De Instrucciones

GB

Product Familiarisation

1 On/Off Switch
2 Lock-On Button
3 Handles
4 Speed Control Dial
5 Gear Selector
6 Output Drive
Unpacking Your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its
features and functions.
Ensure that all parts of the tool are present and in good condition. If any
parts are missing or damaged, have such parts replaced before attempting
to use this tool.
Before Use
Attaching a mixing paddle
WARNING: Always disconnect from the power supply before attaching/
changing accessories.
WARNING: Never fit any attachment with a maximum speed lower than the
no load speed of the machine.
• This plaster mixer is equipped with an M14 female Output Drive (6)
• M14 threaded mixing paddles are fitted by screwing them into the output
drive. Tighten with a suitable spanner
• Ensure that the mixing paddle is securely tightened before use
Operating
On/off switch
WARNING: Always ensure that the power cord is not interfering with the
mixing paddle or presenting a tripping hazard for the operator or other
personnel in the vicinity.
• Grip the mixer firmly by the Handles (3) with both hands
• To start the mixer, press the On/Off Switch (1)
• Press the Lock-On Button (2) to lock the tool in the 'on' position
• To stop the mixer, squeeze the on/off switch and release
Gear selection
WARNING: Do not attempt to change gears whilst the machine is running.
NEVER attempt to run the machine with the gear selector in mid-position
between settings, as this will damage the gear box.
• This mixer is equipped with a 2-speed gearbox
• To select a gear, rotate the Gear Selector (5) to align with the appropriate
marking
Speed selection
• The mixer is fitted with variable speed control
• To alter the speed, simply adjust the Speed Control Dial (4). The higher the
number, the faster the speed
Mixing of material
WARNING: Always wear adequate personal protection equipment when
mixing compounds, including safety goggles or a face shield, breathing
protection (specific to the material used), gloves (suitable for the material
used), hearing protection, and a hard hat where required.
WARNING: This tool is designed for two-handed operation. Never use with
one hand, or attempt to mount stationary or prop-up against another object.
Note: Always refer to the compound manufacturers mixing requirements
and recommendations.
6
• The shape and size of a mixing paddle that is ideal for a specific
application will depend on the type of material being mixed:
• Substances with a low viscosity such as dispersion paint, varnish, thinset,
sealing and levelling compounds, cement, grout etc., will require a mixing
paddle with a left-hand twist
• Substances with a high viscosity, such as ready-mixed plaster, concrete,
screed, putty and epoxy resin, will require a mixing paddle with a right
hand twist
• It is important to keep the paddle moving throughout the bulk of the
material whilst mixing, as opposed to keeping it in one central position in
the mixing container. Mix until compound is completely blended
WARNING: Do not overload the motor whilst mixing. When you recognise
a significant drop in speed, switch off immediately to avoid damage to the
tool. Consider changing to a different mixing paddle or accessory more
suitable for the material.
WARNING: When you have completed the mixing procedure, allow the
mixer to come to a complete stop before lifting it out of the material. Make
sure not to contaminate the environment and clean-up potential spillage.
IMPORTANT: To avoid damage to the machine and cross-contamination
between different materials, always clean the mixing paddle immediately
after use. Don't let the material dry on the accessory. Also, refer to the
paragraph 'Cleaning' in the 'Maintenance' section below.
Accessories
• A range of accessories for your tool, including mixing paddles in
numerous sizes and for different compounds, is available from your
Silverline stockist
Maintenance
WARNING: Always disconnect from the power supply before carrying out
any maintenance/cleaning.
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to
wear quickly and will shorten the machine's service life. Clean the body
of your machine with a soft brush or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Use water, a suitable cleaning solution, or mild solvent to clean rests of
material off the accessory. Wear appropriate protection equipment whilst
cleaning, including eye, hand and breathing protection
Note: Dispose of rest material and contaminated cleaning solution according
to regulations. Recycle where possible. Only use non-water solvents where
absolutely necessary and always follow the manufacturer's guidelines for
safe usage.
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure,
or visible sparking
• If you suspect the brushes may be worn, have them replaced at an
authorised service centre
Storage
• Always remove all material from the accessory, clean and dry the tool
before storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools