Descargar Imprimir esta página

Ecco EW2002B LED Instrucciones De Instalación Y Operación

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

ECCO's EW2002B LED pedestrian spotlight is designed specifically
for material handling applications to provide a visual warning for
pedestrians in the vicinity of mobile equipment. These lights are
intended as a supplemental safety device in addition to a 360°
warning light and project a bright 55 lumen blue spot beam onto the
ground, either in front or to the rear of the vehicle. This additional
safety feature is especially useful where blind corners are present
(i.e. warehouse racking) and is likely to be seen by pedestrians that
are not looking up or paying close attention to their surroundings.
Featuring 12-80 VDC operation, an aluminum housing and
polycarbonate lens, the EW2002B is extremely resistant to impact
and vibration damage and is water and dust resistant.
IMPORTANT!
Read all instructions before installing and using. Installer: This manual must be
delivered to the end user.
!
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is
essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can
operate the system without losing eye contact with the work area.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the
vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks
or compartment doors), people, vehicles, or other obstructions.
6. The manufacturer assumes no liability for any loss resulting from the use of this device.
SAA
NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.
Specifications:
Voltage:
12-80 VDC
Weight:
1.2 lbs.
Lumens:
55
Wiring Instructions:
Black Wire:
Ground
Red Wire:
Connect to fused power, use 3 Amp Fuse
See wiring diagram for further instruction
Installation and Operation Instructions
EW2002B LED WORKLAMPS
Installation:
Place carriage bolt through bottom hole in mounting bracket.
Use a drill bit large enough for a clearance fit of the carriage
bolt and drill a hole in the desired mounting surface location.
Place the carriage bolt through the hole and secure with the
flat washer, the lock washer and the nut. Adjust the beam
location of the unit in the horizontal and vertical directions and
tighten both nuts with a wrench.
Page 1 of 2

Publicidad

loading

Resumen de contenidos para Ecco EW2002B LED

  • Página 1 Installation and Operation Instructions EW2002B LED WORKLAMPS ECCO’s EW2002B LED pedestrian spotlight is designed specifically for material handling applications to provide a visual warning for pedestrians in the vicinity of mobile equipment. These lights are intended as a supplemental safety device in addition to a 360°...
  • Página 2: Customer Service

    Lens Black 3 AMP FUSE Vehicle Body Mounting Position Manufacturer Limited Warranty and Limitation of Liability: Manufacturer warrants that on the date of purchase, this product will conform to Manufacturer’s specifications for this product (which are available from the Manufacturer upon request). This Limited Warranty extends for Thirty-Six (36) months from the date of purchase.
  • Página 3: Luces De Trabajo Led Ew2002B

    LUCES DE TRABAJO LED EW2002B El reflector para peatones LED EW2002B LED de ECCO ha sido diseñado específicamente para aplicaciones de manipu- lación de materiales, para ofrecer una advertencia visual a los peatones cuando se encuentren en las cercanías de equipos móviles.
  • Página 4 ECCO garantiza que, a la fecha de compra, este producto cumple con las especificaciones de ECCO para este producto (que se encuen- tran disponibles de ECCO a pedido). Esta Garantía limitada es válida por un período de 36 (treinta y seis) meses a partir de la fecha de compra.
  • Página 5: Lampes De Travail Del Ew2002B

    LAMPES DE TRAVAIL DEL EW2002B Le projecteur électrique pour piétons EW2002B ECCO est conçu spécifiquement pour les applications de manipulation de matériaux, fournissant un avertissement visuel pour les piétons à proximité des équipements mobiles. Ces projecteurs sont conçus comme dispositifs de sécurité...
  • Página 6 Electronics Controls Company « ECCO » (fabricant) ECCO garantit qu’à la date d’achat ce produit est conforme aux spécifications d’ECCO pour ce produit (qui sont disponibles auprès d’ECCO sur demande). Cette garantie limitée couvre trente-six (36) mois à partir de la date d’achat.