Notch ROPE RUNNER PRO Manual Del Usuario página 10

friction setting. (Fig 6H). Refer to the Friction Adjust-
ment section of the manual for proper friction setting.
• Ensure proper alignment of the connector. (Fig 6I-
Fig 6J)
WARNING: Perform all function principal and
load tests with the Rope Runner Pro at ground level, in a
risk-free environment before working at height. Friction
may require additional adjustment if unintended descent
is detected on the rope, switching climbing methods such
as from using Moving Rope System (MRS) to Stationary
Rope System (SRS), environmental changes (temperature,
moisture, etc.), or changing new, alternative construction
or rope diameter.
Always test the Rope Runner Pro before each use!
7 \ PRECAUTION FOR USE
• Stay below the anchor and ensure the anchor point
is correctly positioned. Ensure the climbing system is
under tension to avoid dynamic shock loading of the
rope. (Fig 7A)
• Do not use the SRS Ascent Attachment Point in MRS
set up. (Fig 7B)
• Ensure the Rope Runner Pro does not bend across
foreign objects while in use. (Fig 7C)
• Ensure proper alignment of the connector. (Fig 7D)
• Any pressure on the Bird presents a fall risk. Monitor
your equipment and the elements of the environment.
(Fig 7E)
• Ensure adequate separation between Rope Runner
Pro and static side of an MRS climbing line to prevent
any interference between the rope and the Bird of the
Rope Runner Pro. Shown with Notch Rook Pulley.
(Fig 7F)
• Keep hair and loose clothing away from moving parts.
(Fig 7G)
18
8 \ USE
Controlling Rope Movement
Rope friction is released by exerting downward pressure
on the front edge of the Bird, allowing the climber to
descend. Use of a second hand below the Rope Runner Pro
is effective in limiting the speed of the rope flow.
(Fig 8A-8B)
Ascend
Ascend using a foot and/or knee ascender. (Fig 8C) A hand
ascender may be used in combination but NEVER with
any type of tether. (Fig 8D) An ascender could become
disabled which would bring it into contact with the
Rope Runner Pro.
WARNING: If a tether is used the users weight
could cause it to descend directly on top of the Rope
Runner Pro. Any contact with the top of the Rope Runner
Pro can cause a drop, and continued contact can cause
uncontrolled descent, possibly resulting in serious injury
or death.
Do not allow the Rope Runner Pro to get out of reach
of the user.
Descend
To release friction and initiate descent exert downward
pressure on the front edge of the Bird. To stop descent,
release all pressure from the Rope Runner Pro. (Fig 8E)
Creep and uncontrolled descent are possible due to a
variety of factors including, but not limited to:
• Incorrect rope size or type.
• Component wear.
• Improper use or installation.
If creep or uncontrolled descent occur, push up on the
Bird assembly to stop or slow descent.
WARNING: This device has no panic feature.
Stopping requires releasing the device completely.
Continuous downward pressure on the Bird will result
in rapid descent leading to potential injury or death.
Be aware of high temperatures during long descents.
Monitor the condition of your rope and inspect for
damage if you suspect high temperatures.
Lateral Movement
• Move away from the anchor point by depressing the
Bird assembly of the Rope Runner Pro and allowing the
rope to pass upwards through the device. (Fig 8F)
• To return toward the anchor point pull the rope down
and outward through the bottom of the device while
advancing toward the anchor point. (Fig 8G)
• Never allow slack to enter your system! Always
maintain tension on your system to prevent dangerous
shock loading! (Fig 8H)
WARNING: Do not use the redirected tail of the rope
to control your position or descent. Holding the redirected
tail can collapse the device, causing unexpected descent,
and the tail will move through your hands faster due
to mechanical advantage. If uncontrolled descent occurs,
release the rope and the device to allow the
Rope Runner Pro to engage. (Fig 8I)
9 \ ADDITIONAL INFORMATION
This product meets requirements of the ANSI Z133-2012
standard.
Lifespan
Product has indefinite lifespan. (Fig 9A) It is very difficult
to estimate lifespan due to varied use and storage
conditions. However, the following may greatly reduce the
strength of the product and consequently the lifespan:
incorrect use, severe fall arrest, mechanical deformation,
fall from a height on the product, general wear and tear,
chemical and heat contamination.
Cleaning
If necessary clean with fresh water then allow to dry
completely. Store in a dry place away from extremes of
heat and cold and avoid chemical exposure. (Fig 9B-9C)
Storage & Transport
During transportation or after any necessary cleaning,
drying and lubrication, store unpacked in a cool, dry, dark
place in a chemically neutral environment away from
excessive heat or heat sources, high humidity, sharp edges,
corrosives or other possible causes of damage. Do not
store wet. (Fig 9D)
Repairs or Modifications
Do not repair or modify your product in any way unless
specifically authorized in writing by the manufacturer.
(Fig 9E)
Lubrication
Perform lubrication every 1000 hours of use or every year,
if applicable. Apply a few drops of a 3-IN-ONE Mineral Oil
Lubricant in the Lubrication Port. Allow to soak in. Lubri-
cation should be carried out after cleaning. (Fig 9F)
When to Retire from Service
Immediately retire any equipment if:
• The product fails any inspection (before, during, after
use and periodic in-depth inspection).
• It has been exposed to a fall or was significantly loaded.
• It was misused, altered, damaged, or exposed to
harmful chemicals. (Fig 9E)
• There is any doubt regarding its integrity.
Obsolescence
A product may become obsolete before the end of its
lifespan. Reasons may include changes in applicable
standards, regulations, legislation, development of new
techniques, incompatibility with the other equipment, etc.
Rescue Plan
It is important to make a plan for a rescue in the event
of an emergency BEFORE starting to work. It is also im-
portant to ensure the user and/or the employer has a doc-
umented rescue plan and can implement it. This implies
an adequate training in the necessary rescue techniques.
10 \ TRACEABILITY AND MARKINGS
Do not remove any markings or labels. Markings must
remain legible during the entire lifespan of the product.
The product can be traced through its own markings and
19