Publicidad
Idiomas disponibles
Idiomas disponibles
Instruction manual
V0.0
Bills embedder
CONTENT AND DESCRIPTION
EMBEDDER
Tape feeder mechanism
Control Panel
Presence sensor
Mouth of access for bills
POWER CABLE
PREPARATIONS
1. Connect the power cable (interlock) to the connector of the shroud, and set the switch to I to turn
on the equipment.
3. Pass the tape through the rollers.
Side with adhesive
5. Enter a wad of bills in the access manhole. When you are sure of the location where you require the band, bring the bundle to the sensor.
Maximum 100 bills
ADJUSTMENTS
Set the temperature setting to paste the tape (100 to 150 ° C) by
TEMPERATURE
pressing CLR repeatedly to increase it or SET to decrease it.
0
Enlace
Total
Temp
State
119
ºC
Before
CLR
Exit
SET
SPECIFICATIONS
Input: 110 V
60 Hz 60 W
Consumption: <60 W / h
Standby consumption: <3W / h
Operating temperature: 0 - 40 ° C
Relative humidity: <85% non-condensed
Specifications may change without prior notice
BILL-300
PRECAUCIONES
Cover
Handle
Connector for cable (Interlock)
Depth adjustment knob
On / off switch
Enlace
Total
Temp
110
ºC
CLR
Enter
Exit
SET
IMPORTANT
Before using the product, carefully read this instruction manual to avoid any malfunction.
The information presented serves only as a reference; Due to updates there may be differences.
Check our website www.steren.com for the latest version of this manual.
CAUTIONS
• This device is not intended for use by persons (including children) whose physical, sensory or mental
abilities are different or reduced, or who lack experience or knowledge.
• Children should be supervised to make sure they do not use the device as a toy.
• Do not place heavy objects on the frame.
• Do not use or store the girdler in places where there are leaks, humidity or splashes.
• Clean it with a soft, dry cloth.
• Do not insert the hand (s) or any other object in the ticket opening, while the spacer is on.
0319A
CONTROL PANEL
Actual temperature
Increase temperature
THERMAL TAPE
2. Open the lid, and place the tape.
4. Fold the tape down and close it to the feeder mechanism; then press
nism will pull the necessary tape for the first enjailed.
If the tape is bent or poorly adapted, the message "Plug Paper"
will appear in the Current Status segment; press
remove the tape, cut the folded section and repeat step 4.
Side with adhesive
In the current Status segment "Run"
will appear
DEPHT
The depth adjustment helps to place the bar at the
same level on all bills.
Turn the knob to give more or less depth to the top.
0
State
After
Enter
WARRANTY POLICY
This Steren product is warranted under normal usage against defects in workmanship and materials to the original purchaser for one
year from the date of purchase.
CONDITIONS
1. This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be
presented when warranty service is required.
2. If the product is in the warranty time, the company will repair it free of charge. The supplier will pay for transportation charges.
3. The repairing time will not exceed 30 natural days, from the day the claim was received.
4. Steren sell parts, components, consumables and accessories to customer, as well as warranty service, at any of the addresses
mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions,
improper repair by unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer ____________________________________
Address _____________________________________________
Serial number ________________________________________
Product ______________________________________________
ELECTRÓNICA STEREN S.A. DE C.V.
Biólogo Maximino Martínez No. 3408, San Salvador Xochimanca, Del. Azcapotzalco Ciudad de México 02870, RFC: EST850628-K51
STEREN PRODUCTO EMPACADO S.A. DE C.V.
Autopista México-Querétaro. Km 26.5 Sin número, Nave Industrial 3-A, Col. Lomas de Boulevares, Tlalnepantla de Baz, Estado de
México, C.P. 54020, RFC: SPE-941215-H43
Enlace
Total
Temp
144
ºC
CLR
Remove tape
Exit
SET
Decrease temperature
Less depth
Producto: Bills embedder
Model: BILL-300
Brand: Steren
In case your product fails or have questions, please contact your nearest dealer.
If you are in Mexico, please call to our Call Center.
01 800 500 9000
Counter
0
State
Actual state
Thread tape
Enter
. The mecha-
Enter
to
Exit
Side with adhesive
When the band is ready, remove the
bundle.
More depth
Publicidad
