Summary Of Operation; Technical Support - Aleratec 1:7 USB HDD Copy Cruiser SA Guia De Inicio Rapido

Summary of Operation

Synchronous Copying (for greater than 256MB)
In Synchronous Copying all USB flash drives are copied simultaneously.
1. Load the source flash drive into the USB Duplicator. Use the UP or
DOWN arrow to scroll through the menu until Copy is displayed on the
LCD screen.
USB Duplicator
1. Copy (Data) or (Whole)
2. Press the OK button on the display panel. The LCD will display the
following status:
USB(963M) 450M
0 to start...
Note: The number beside "USB" is the capacity of the USB flash
drive in megabytes. The number to the right is the size occupied
by files or images.
3. Load the blank target flash drives into the USB Duplicator. The LCD will
display the number of blank media loaded and ready for copying.
USB(963M) 450M
3 to start...
4. Finish loading the blank target flash drives, then press the OK button on
the display panel.
5. The LCD will display the status of the copying process.
Port number of slowest target drive
Copy
15%
Percent complete
6. When Copy is complete LCD will display the following status:
Total OK: 5 OK: 5 NG: 0
01:03 OK: 5 NG: 0
If the Copy fails, the LCD will display the number of flash drives that
failed and passed.
Note: When copying is in process the Green LED on the front
panel is blinking. Do not take out the drive while it is copying.
When copying is finished the Green LED stays on (no blinking). If
an error occurs during the copy process a Red LED will display.

Technical Support

E-mail: support@aleratec.com Skype: support.aleratec.com
Phone: +1-818-678-0484 FAX: +1-818-678-0483
Technical Support Group can be reached 8:00 AM to 5:00
PM, Pacific Time, Monday through Friday, excluding U.S.
holidays. Please try to call from a phone near your computer
system. Access is available 24 hours a day, 365 days a year,
via: The World Wide Web at: www.aleratec.com
© 2014 Aleratec, Inc. 9851 Owensmouth Avenue Chatsworth, CA 91311 U.S.A.
Specifications subject to change without notice.
Total MBytes
on source
450M
(3) 68M
MBytes copied
Document Number:
Menu:
Function
1. Copy
2. Compare
3. Copy+Compare
4. Overwrite
5. Information
5.1 USB Info
5.2 System Info
6. Utility
6.1 Do Format
6.1.1 Auto Format
6.1.2 FAT16 Format
6.1.3 FAT32 Format
6.1.4 Set FAT16
Cluster Size
6.1.5 Set FAT32
Cluster Size
6.2 System Update
7. Setup
7.1 Startup Menu
7.2 Copy Area
7.3 Button Sound
7.4 Target Tolerance
7.5 Asynchronous
7.6 Power Off Time
Between Copy
and Compare
7.7 Language
7.8 Set Default
330120-330121_QSG_ENG_Rev_A
Description
This option performs a copy from a source drive to one
or more target drives.
This option makes a bit-by-bit comparison between
source drive and all other copied drives.
This option will make a copy first and then compare the
copied drives with the source drive right after copy function.
This function will sanitize 2.5 external USB hard disk
drives using 1-Pass, 3-Pass or DOD 7-Pass Overwrite.
This function will show the USB basic information such
as media type, content size and available space.
This function will provide information about the
duplicator including firmware version.
This function is used to format drives with the duplicator.
If the drive is less than 2GB the duplicator will format
FAT16. If the drive is larger capacity than 2GB then the
duplicator will format FAT32.
This function will format your drives in FAT16 format.
This function will format your drives in FAT32 format.
This function will set the cluster size for FAT16 format.
This function will set the cluster size for FA32 format.
This function is used to update your duplicators
firmware.
You can select which function is shown first when your
duplicator is powered on.
With this function you select Quick Copy or Copy whole
area of the source.
You can choose whether to hear a beep when you press
a button or not.
This function is used to set the tolerance % of capacity
difference between source and targets.
This function allows the user to enable/disable
asynchronous copying.
This function will set the wait time before automatically
starting the compare process after the copy process has
completed.
This function selects the language shown on the display
(English and Japanese).
This function will reset all settings to their original
values.