Tabla de contenido
Publicidad
Enlaces rápidos
Model #
133Wa
Kingston Barstool
Assembly Instructions
Congratulations!
This fine piece of furniture will make a handsome
addition to your home. For the best results, start by
reading both the Assembly Instructions and
Finishing Hints before you begin your project.
For normal household use only.
recommended for commercial use.
Do not climb or stand on this piece of
furniture.
P.O. Box 2827
Eugene, OR 97402 USA
Service Policy:
which are defective, missing or damaged
during assembly. Please contact Whittier
Wood Products customer service department
directly (by phone, fax, mail or email) for
replacement parts.
Hours:
Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order:
Provide the complete furniture
model number (upper left corner of this
page), part letter, production code, quantity
needed, reason for replacement and your full
name and address along with a telephone
number in case we need to contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
O O u u t t s s ide
ide U U . . S. or Canada:
S. or Canada: 5 5 4 4 1 1 - - 6 6 8 8 7 7 - - 0 0 2 2 1 1 3 3
F F a a x: x: 5 5 4 4 1 1 - - 6 6 8 8 7 7 - - 2 2 0 0 6 6 0 0 • • ww
M M a a i i l l : : P P .O .O. . B B o o x 28
x 282 2 7 •
7 • E E ugen
Read both the Assembly Instructions and Finishing
Hints completely before beginning.
Store the parts: 1) in their box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may
be affecting the stability of your furniture. Tighten or
repair as needed.
Production Code:
VN
We will replace any parts
www w . . w w h h i i t t t t i i e e r r w w oo
ood d . . c c o o m m
ugene e , , O O r r egon
egon 9 9 7 7 4 4 0 0 2, 2, U U . . S S . . A A . .
Rev. 3/07
Publicidad
Tabla de contenido
Manuales relacionados para Whittier Wood Products Kingston 133Wa
Resumen de contenidos para Whittier Wood Products Kingston 133Wa
- Página 1 Model # 133Wa Kingston Barstool Assembly Instructions Service Policy: We will replace any parts which are defective, missing or damaged during assembly. Please contact Whittier Wood Products customer service department directly (by phone, fax, mail or email) for replacement parts. Hours: Our friendly customer service staff can be reached Monday-Friday 7:00 a.m.
- Página 2 133Wa Kingston Barstool — Parts List Before beginning assembly, check that the quantities of the parts received match those on the parts list below. A — Bottom Back — Qty. 1 I — Left Arm — Qty. 1 B — Back Slat — Qty. 4 J —...
-
Página 3: Tools Required
133Wa Kingston Barstool — Parts List (cont.) XX — Allen Wrench — Qty. 1 U — Wooden Button — Qty. 2 R — Brass Ring — Qty. 1 YY — 50mm x 1/4" Brass V — Dowel — Qty. 2 S —... - Página 4 NOTE: CURVED EDGE TO FRONT! SHOULDER 2" LONG 1¾" LONG FRONT FIG. 2A FIG. 2 VIEW Lay the back assembly between the Left Back Post (D) and the Right Back Post (EE). THE CURVED TOP EDGE OF THE BACK POSTS SHOULD FACE TOWARD THE FRONT OF THE CHAIR. THE LEFT BACK POST (D) HAS A LARGER UPPER SLOTTED HOLE AND THE TOP BACK (CC) HAS A LARGER TENON ON THE LEFT SIDE.
- Página 5 RING GROOVE (facing out) FIG. 5 FIG. 4 Place the Disc (K), top side down, on your work surface. (The top side is marked with indentations for attaching the swivel later.) Spread glue in each leg hole in the disc. Put a Leg (M) in each hole with the straight edge with the ring groove toward the outside and tap into place as shown in Figure 4.
- Página 6 FIG. 8 Cover the work surface with a cloth or piece of cardboard to protect the seat and arms. Place the seat upside down on the work surface. Be sure that the front of the swivel is placed towards the front of the seat and place the leg assembly upside down on the bottom of the seat and line up the holes in the swivel with the pilot holes in the seat.
-
Página 7: Instrucciones Para Armar
Modelo # 133Wa Banqueta de bar Kingston Normas para obtener servicio: Reemplaza- remos las piezas que tengan defectos, falten o se Instrucciones para Armar dañen durante el armado. Sírvase comunicarse con el departamento de servicio al cliente de Whittier Wood Products directamente (por teléfono, fax, ¡Felicitaciones! correo o e-mail) para obtener piezas de repuesto. -
Página 8: Instrucciones De Ensamblaje
Banqueta de bar Kingston 133Wa INSTRUCCIONES DE ENSAMBLAJE HERRAMIENTAS NECESARIAS: Destornillador Phillips, destornillador común, maza de goma o martillo forrado, cola para madera, taladro y barrena de 1/8". IMPORTANTE: ANTES DE ENSAMBLAR, LEA LAS INSTRUCCIONES PARA USAR EL PEGAMENTO. No es para uso de niños a menos que cuenten con la supervisión de un adulto. - Página 9 Banqueta de bar Kingston 133Wa la tuerca. Utilice la llave Allen (XX) para apretar los Gire la parte superior de la placa giratoria (L) 1/8 de pernos hasta que queden firmes. NOTA: AL USAR vuelta con relación a la parte inferior. La placa girato- LA LLAVE ALLEN, ESTA DEBE QUEDAR ria está...
-
Página 10: Tabouret De Bar Kingston
No. de modèle 133Wa Tabouret de bar Kingston Politique de service : Nous remplacerons toutes Instructions de Montage les pièces défectueuses, manquantes ou endom- magées pendant le montage. Veuillez contacter directement le service clientèle de Whittier Wood Félicitations ! Products (par téléphone, fax, courrier ou e-mail) Ce joli meuble s’intègrera agréablement à... -
Página 11: 133Wa Tabouret De Bar Kingston
133Wa Tabouret de bar Kingston INSTRUCTIONS DE MONTAGE Outils nécessaires : tournevis cruciforme, tournevis pour écrous à fente, maillet en caoutchouc ou maillet rembourré, colle à bois, foret et mèche de 1/8 po. IMPORTANT : LIRE LES CONSEILS DE COLLAGE AVANT LE MONTAGE ! Non destiné... - Página 12 133Wa Tabouret de bar Kingston l’autre verrou rond dans la plaque en laiton, puis Faites tourner le dessus du pivot (L) de 1/8 de tour dans l’écrou de tension. À l’aide de la clé Allen par rapport au bas. Le pivot porte les indications « (XX), serrez fermement...