GEV CSS Manual Del Usuario página 4

Colour surveillance system CSS
Control elements
Monitor (fi g. A)
1 Camera 1 switch
2 Automatic camera change
3 Camera 2 switch
4 ON/OFF switch
5 Camera switch interval: setting 5 - 50 seconds
6 Volume
7 Camera 1 connection socket
8 Camera 2 connection socket
9 Power supply 12 V connection socket
10 Attachment wall holder/table stand
11 Loudspeaker
12 Wall holder
13 Table stand
Camera (fi g. B)
1 Camera lens
2 IR LEDs
2A Light sensor
3 Microphone
4 Wall holder
5 Cable 18 m
6 Plug
Power supply (fi g. C)
Safety information
All warranty claims will be null and void in the
event of any damage or loss caused by failure
to observe these operating instructions.
We accept no liability for any consequential
losses or damage. We accept no liability for any
personal injury or material damage caused by improper
use or by failure to observe the safety advice. In these
cases the guarantee and warranty are invalidated. For
safety and authorisation purposes it is not permitted to
carry out any adaptation or conversion of the device.
Mounting
If you are unsure of how to assemble, connect and
install the device or if you are in doubt as to how to
operate it, please do not assemble, connect or install
the device yourself but contact a qualifi ed specialist.
Please observe the position of the camera when
mounting as shown in fi g. D and mount so that it is not
exposed to direct environmental eff ects such as rain.
The microphone opening B3 must face down.
The monitor can either be attached to the wall (fi g. E1)
using wall holder A12 or placed on a table top (fi g. E2)
using table stand A13. Clip the wall holder or table
stand into the appropriate attachment A10 on the
monitor in the selected position.
Connection (fi g. F)
Connect plug B6 from the fi rst camera into connection
socket camera 1 (A7) on the monitor. You have the
option of connecting a second camera (not supplied)
to camera 2 connection socket (A8). Connect the
power supply plug (fi g. C) to connection A9 and insert
the plug into the appropriate socket. Only use GEV
system cameras, as cameras/devices from other
suppliers may damage the colour surveillance system
CSS.
Starting up/operating
Press the ON/OFF key (A4). The LED in the key lights
up if there is mains power and the monitor displays the
image from camera 1.
The volume is adjusted using the loudspeaker
controller (A6). Direct the camera as required.
If a second camera is also connected, press the
Camera 2 (A3) key and set as required. The images
from cameras 1 and 2 can be shown in sequence.
Press the automatic camera switch key (A2). The
interval can be infi nitely adjusted from 5 - 50 sec.
using the switch interval controller (A5). An LED
is integrated into keys A1, A2, A3 and A4 to
indicate the settings.
The cameras are fi tted with IR LEDs to allow persons
and objects to be identifi ed within a range of
approx. 1 m, even in the dark (for technical reasons
these images are only available in black and white).
Optional accessories (fi g. G)
Heated camera (art. no. 085091)
A heated camera will need to be used in cold climates.
This camera is designed for external temperatures
down to -25 °C. Connect the camera plug B6 to camera
socket 1 or 2 (A7 or A8). The heated camera works in
exactly the same way as the standard camera.
If you intend to use 2 heated cameras (Item no.
085091), the 1000 mA power pack provided with the
display must be exchanged for a 2000 mA power pack
(Item no. 085138).
Recycling instructions
This device must not be disposed of with unsorted
household waste. Owners of old devices are
required by law to dispose of this device correctly.
Contact your town council for further information.
4
Troubleshooting – practical tips
Problem Cause
No picture and ON/OFF Is the wall power supply connected?
LED does not light up
No picture and ON/OFF Wall power supply is faulty/
LED does not light up monitor is faulty
No picture/faulty picture Is the camera connected?
Is the camera cable damaged?
Camera is faulty
Picture rotated by 180° Camera has been mounted upside
down
Picture is black and white Night image, caused by IR LEDs
Whistling sound Camera is too close to monitor
No sound/sound too quiet Volume is set too low
No sound Is the camera cable damaged?
Camera microphone is faulty
Technical data
Monitor
Dimensions
Display type
Resolution
Voltage
Standby mode power consumption
Operating power consumption
Operating temperature range
Camera
Dimensions
Camera module
Resolution
Exposure time
Min. lighting
Operating voltage (supplied by monitor)
Operating power consumption
Operating temperature range
Max. cable length
Protection type
Power supply 1000 mA
Input voltage
Output voltage
Rated current
Power supply 2000 mA
Input voltage
Output voltage
Rated current
Gutkes GmbH
Rehkamp 13 Fax: +49 (0)511/95 85 805
30853 Langenhagen www.gev.de
Germany service@gev.de
Solution
Connect wall power supply
Take wall power supply/monitor for
inspection if necessary
Check plug
Check and if necessary replace
cable
Check and if necessary replace
camera
Mount camera with the
microphone facing down
Normal for night time surveillance
Reposition camera
Set the volume
Check and if necessary replace cable
Check and if necessary replace
camera
approx. W 120 mm x H 126 mm x D 32 mm
TFT 3.5 inch (visible diagonal measurement 87 mm)
480 x 234 pixels
12 V
approx. 1 mA
approx. 180 mA
-10 °C to +45 °C
approx. W 57 mm x H 80 mm x D 70 mm
CMOS 1/3 inch
628 x 582 pixels
automatic 1/60 to 1/15000 sec.
< 3 Lux (at a distance of < 50 cm)
8 - 13 V
approx. 70 - 100 mA
-10 °C to +45 °C
approx. 72 m
IP 44
230 V ~, 50 Hz
12 V
max. 1 A
230 V ~, 50 Hz
12 V
max. 2 A
We reserve the right to make technical and
visual modifi cations without prior notice.
5