Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
IT IS THE RESPONSIBILITY OF THE OWNER
TO MAKE SURE ALL PERSONNEL READ THIS
MANUAL PRIOR TO USING THE DEVICE.
IS ALSO THE RESPONSIBILITY OF THE DEVICE
OWNER TO KEEP THIS MANUAL INTACT AND
IN A CONVENIENT LOCATION FOR ALL TO SEE
AND READ.
LABELS ARE LOST OR NOT LEGIBLE, CONTACT
MATCO TOOLS FOR REPLACEMENTS.
OPERATOR IS NOT FLUENT IN ENGLISH, THE
PRODUCT AND SAFETY INSTRUCTIONS SHALL
BE READ AND DISCUSSED WITH THE OPERATOR
IN THE OPERATOR'S NATIVE LANGUAGE BY
THE PURCHASER/OWNER OR HIS DESIGNEE,
MAKING
COMPREHENDS ITS CONTENTS.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig; 6.2 bar max
air pressure with 3/8" diameter air supply hose.
• Always
wear
protection
maintenance on this tool (users & bystanders).
• Always wear hearing protection when using this
tool
(users
levels
can
loss. Use hearing protection as recommended by
your employer or OSHA regulation.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and
power of this tool.
• Keep tool out of reach of children.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if discomfort,
tingling feeling or pain occurs. Seek medical advice
before resuming use.
• Compressed air can cause severe injury. Never direct air
at yourself or others. Always turn off the air supply, drain
hose of air pressure and detach tool from air supply
before installing, removing or adjusting any part
or accessory on this tool, or before performing any
maintenance on this tool. Failure to do so could result
in injury.
SE214
SE214 1/4˝ Air Hydraulic Rivet Gun
IF THE MANUAL OR PRODUCT
SURE
THAT
THE
OPERATOR
impact-resistant
eye
when
operating
or
&
bystanders).
High
cause
permanent
WARNING
IT
IF THE
or
face
performing
sound
hearing
2
• Whip hoses can cause serious injury. Always check for
and replace immediately any damaged, frayed or loose
hoses and fittings.
• This tool is not insulated against electric shock.
• This tool must not be used in explosive atmospheres.
• Do
not
lubricate
tools
volatile liquids such as kerosene, diesel or jet fuel.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Use replacement parts and accessories recommended
by Matco Tools.
• Servicing and repairs should only be made by an
authorized service center.
• Do not use (or modify) the tool for any other purpose
than that for which it was designed without consulting
the manufacturer's authorized representative.
• Risk of electric shock.
• Explosive atmosphere warning
• Keep clear of trigger when inserting rivets.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
thoroughly after handling.
• Failure to heed these warnings may result in serious or
fatal personal injury and/or property damage.
NOTE: During operation, safety goggles must always be
worn to guard against flying rubber (users & bystanders).
with
flammable
or
rev. 03/25/16
Publicidad
Tabla de contenido
