Publicidad
Idiomas disponibles
Idiomas disponibles
USER INSTRUCTION MANUAL [EN]
IMPORTANT NOTICE TO USERS
Series 2000 reusable half mask respirators must be used and
maintained in accordance with this instruction manual. You are
responsible to understand and follow all warnings, restrictions
and other information contained in this instruction manual
before you enter a contaminated work area. Incorrect use, use
of unsuitable spare parts or bad maintenance are dangerous for
health and safety and exonerate the manufacturer from all liability.
Personal protective equipments for respiratory protection must
always be used by specially trained people. The use has to be
supervised by a person perfectly aware of the limits of application
and of the applicable laws concerning those devices.
MPL S.L.
86, Carles Buïgas - 08187 - Santa Eulàlia de Ronçana
Barcelona - Spain |
info@mplsl.eu
|
www.mplsl.eu
The product has been examined in its design stage by CNMP,
Notified Body nº0159, Carabela La Niña, 16, 41007 Seville, Spain.
It has been shown that this respirator meets the health and
safety requirements under modules B and C2 of the Regulation
(EU) 2016/425. Series 2000 respirators are CE marked and have
been tested according to the requirements of EN 140:1998 as
Category III PPE.
APPLICATIONS
Series 2000 half mask respirators mask can be used in
conditions requiring respiratory protection and must be used only
with Series B bayonet connection filters.
MARKING
Each respirator is marked on the front cover as following:
•
Series 2000 Model.
•
The standard that the respirator meets as per the Regulation
(EU) 2016/425, EN 140:1998.
•
CE marking with nº of the Notified Body in charge of respirator
product control according to C2 module of Regulation (EU)
2016/425, Notified Body 0161, AITEX, Emilio Sala, 1, 03801 Alcoy,
Spain.
WARNINGS AND RESTRICTIONS TO USER
•
This half mask does not supply oxygen (O2), and must be used
in a ventilated work environment with an oxygen volume superior
or equal to 17%.
•
Use the appropriate filters in each case, depending on
concentration and type of contaminant.
•
Series 2000 are twin filters reusable respirators.
•
Do not use as protection against Carbon Monoxide.
•
Do not alter or modify this respirator.
•
Do not use this respirator in containers, pits, sewers or con ned
places with no ventilation.
•
Any facial feature hindering the perfect sealing of this respirator
(e.g. beards) must be removed.
•
If the respiratory equipment is damaged, or if the user has
breathing difficulties and/or feels ill or faint, the work area must
be abandoned immediately.
Series 2000 - 20UIM - v5
Page 2
BEFORE EACH USE
Inspect your respirator before and after wearing. Don't wear, and
return to your supervisor if:
•
Head straps are torn, cut, or have lost elasticity.
•
Buckles or head cradle are missing, damaged or broken.
•
Facepiece is cracked, torn, distorted, dirty, or has holes.
•
Inhale/exhale valves are missing, torn, damaged, or not properly
seated.
•
Make sure the type of filter selected is appropriate for the
specific use of the half mask.
•
Filters are cracked, damaged, or not properly seated.
•
Any other plastic part is cracked, distorted, or damaged.
FITTING INSTRUCTIONS
Loosen the elastic straps pulling the buckles on the head harness.
•
Place the respirator under the chin and pull the cradle to the top
of the head so it rests on the crown.(Fig. 1)
•
Tighten the top straps first so facepiece should not be loose or
slide up or down nose.
•
Attach the bottom straps directly against the back of the neck.
(Fig. 2)
•
Tighten the lower neck straps.(Fig. 3)
USER SEAL CHECK
Perform both negative and positive seal check each time before
you enter a contaminated area.
Negative pressure seal check Cover the filters and gently inhale
and hold your breath. The facepiece should slightly collapse. If air
leakage is detected, re-adjust the position of the facepiece and
the tension of both head straps and repeat the seal check until
leakage is eliminated.(Fig. 4)
Positive pressure seal check Cover the exhale valve vent and
exhale gently to create a slight positive pressure. If air leakage is
detected, re-adjust the position of the facepiece and the tension
of both head straps and repeat the seal check until leakage is
eliminated.(Fig. 5)
WARNING If you cannot obtain a proper fit, do not enter the
contaminated area and see your supervisor.
Seal check your respirator each time before you enter and
periodically while wearing the respirator in the contaminated area.
MAINTENANCE
The effective life of the respirator will be influenced by the use
conditions and contaminants to which it is exposed. It is highly
recommended to follow next steps after every use:
1. Check if the material shows any signs of cracking, wrinkling, or
aging. If so, then discard the facepiece immediately.
2. Store the respirator, cleaned, in a sealed bag.
EU Declaration of Conformity available on:
www.mplsl.eu/s/series-2000-doc.pdf
CLEANING AND DISINFECTION
Cleaning is recommended after each day's use or more frequently
if necessary:
1. Remove the filters before proceeding with the cleaning.
2. Gently scrub the facepiece with a soft brush in a mild
germicidal detergent, rinse with clean water and air dry. Don't use
solvents to wipe or clean the facepiece as these will reduce the
life of the respirator and pose a health hazard to the user.
3. Dry the half mask thoroughly.
REPLACEMENT PARTS
In case of cracking, wrinkling or aging, spare parts can be
replaced without using any tools: inhale/exhale valves and head
harness assembly.
STORAGE
When not in use or during storage, do not expose respirator to
excessive heat (above 50ºC) or hazardous substances.
LIMITATIONS
Respirators may reduce but do not eliminate wearer exposure
to airborne hazards or the risk of contracting any disease or
infection. Only use this respirator as part of a comprehensive
respiratory protection program. You will receive no respiratory
protection if this respirator is not properly fitted and worn. It is
imperative that you determine the size and potential hazards that
may be present in the environment before selecting appropriate
respiratory protection.
PACKAGING
Every respirator is supplied in an individual case with this
instruction manual for the user included.
Fig.
1
Fig.
2
Fig.
3
Fig.
4
Fig.
5
LIST OF PARTS FOR Series 2000
Nº PART #
DESCRIPTION
N-100N
EPDM FACEPIECE
1
N-100S
SILICONE FACEPIECE
F-100
TPE FACEPIECE
2 N-102
FILTERS HOLDER
3 N-114
FRONTAL COVER
4
N-118
FILTERS HOLDER HOOP
5 N-119
INHALE VALVE
6 N-120
EXHALE VALVE
7 N-116
BUCKLE
8 N-140
HEAD HARNESS
9 N-139
STRAP
REPLACEMENT PARTS FOR Series 2000
PART #
DESCRIPTION
SK-21
VALVES KIT
SK-22
HEAD HARNESS ASSEMBLY
8
9
6
1
2
7
4
5
3
86, Carles Buïgas
08187 Santa Eulàlia de Ronçana
Barcelona - Spain
Publicidad
