Bayco 2120 Manual De Instrucciones

Operating Instructions For
Model 2120 Rechargeable
Under-Hood Work Light
INS-2120-12
CAUTION
DO NOT use in explosive atmospheres, near flammable liquids, or where explosion proof
lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of flammable
liquids coming into contact with the lamp
DO NOT immerse in water
DO NOT use in areas where water can accumulate or in rain or mist
IMPORTANT SAFETY INSTRUCTIONS
This product has a polarized plug (one blade is wider than the other). As a safety feature, this
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord
unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
WARNING: NOT FOR USE IN HAZARDOUS LOCATIONS
Thank you for purchasing this Bayco work light. Save these instructions.
Please read these instructions before using your work light. Be sure to charge the work
light before the first use.
PRODUCT DESCRIPTION & PERFORMANCE

The 2120 under-hood rechargeable work light has two rows of 60 super bright white
LEDs.

The light is integrated into a spring loaded carrier that is ideal for hands-free lighting
while attached to an automotive hood and extends to 77 inches. The light can be
removed from the carrier.

The end-handles are cushioned to prevent scratching and contain the control
switches.

The end caps provide additional two-away mounting via the magnet cluster or
hanger-hooks.

The light is powered by an internal NiMH battery for long run-time and no-memory
charging.
Function Work Light • Run-Time
1 row 60 LEDs • 150 Lumens • 6.5 hrs
2 rows 120 LEDs • 330 Lumens • 3.5 hrs
CHARGING
Initial use
Fully charge the work light before the first use. If the light is new or has been unused for
several months, several charge and discharge cycles may be needed to reach full battery
capacity. To reach maximum performance, run the light to completely discharge the
battery and then recharge. Each charge cycle will extend the operation time until
Charge Time
6 hrs
AC or DC
BAYCO • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • www.baycoproducts.com
maximum capacity is achieved. The charge time for maximum capacity is approximately
6 hours.
Daily use
Use only the supplied AC or DC charging adapter.
 Connect the AC or DC power adapter to the light. The red indicator will light.
 The red light indicates the work light is being charged. The red light remains on until
the battery is fully charged. At full charge, the light turns green. The total time to full
charge varies depending on the remaining charge in the battery pack.
 The battery will not be harmed if the light is charged beyond full charge.
 The light can be used while being charged.
SAFETY
CAUTION BRIGHT LED RADIATION: AVOID DIRECT EYE EXPOSURE. THE LIGHT
IS A CLASS 2 LED PRODUCT PER IEC 60825-1 EDITION 1.2.2001.
 Do not use or charge this work light in explosive or hazardous areas.
 Do not attempt to repair or disassemble the work light or the charger power supply.
 Use only the supplied AC or DC charger.
TIPS TO EXTEND BATTERY LIFE
The work light NiMH internal battery pack does not have a memory effect. Charging the
work light often helps extend its useful life.
 A new work light or one that has not been used for a long period of time may not
accept a full charge initially. This is normal and does not indicate a problem. Fully
discharge and then charge the unit several times to condition the battery pack for full
capacity. As the battery pack capacity increases the charge time shortens.
 Charge the unit after each use, whether the work light is fully discharged or not.
 Store the work light at room temperature
OPERATION
The work light has two switches that work in tandem, one in each end of the light so the
light can be controlled by either switch regardless of which switch is pressed first.
The switches have 3 functions
First press - One row of LEDs
Second press - All LEDs on
Third press - all LEDs off.
HOOD MOUNTING
Using the spring-loaded carrier

Snap the work light into the spring-loaded carrier.

Hook one end of the carrier on the hood. While holding the light extend the opposite
hook to grasp the hood

Control the lights as needed

The light can be rotated in the carrier about 90° for maximum illumination
Using the hanger-hooks

Rotate the centers of each end handle to expose the recessed hanger-hook. Grasp
the hanger-hook and turn out for use
 Hang the light using the hooks
Using the end-magnets