Time Setting; Alarm Setting; Alarm On/Off - Adler AD 1176 Manual De Uso

batteries inside.
Description of the device. ( Weather Station)
1. Control panel: Buttons 1.a. MODE, 1b.UP, 1.c. DOWN, 1.d. ALARM, ,1E. Max/Min 1G. SNOOZE/LIGHT，
Display:
1. Clock 2.Inside temperature 3. Outside temperature 4. Probe 5. Weather Forecast 6. Alert Indicator
2. Operation Instruction
Insert the battery (2xAA) into the device or connect adapter after a few seconds, LCD will light up, after a beep, it enters default mode.
Into the probe insert 2x AAA battery.

2.1 Time Setting

Under default state, press and hold "MODE"(1a) for 4 seconds to enter setting in sequence, the time will start to flash.
Setting item blinking at 1s frequency.
Press "UP"(1b) key, the data goes up one step; press and hold for 2 seconds or more, it will go ahead at 8 steps per second speed.
Press the "DOWN"(1c) key, the value goes down one step; press and hold for 2 seconds, go back at 8 steps per second speed.
After setting, press "MODE"(1a) to confirm/exit.
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
The order of the setup goes as follows:
Hour FORMAT 24/12h → Hour → Minute→ Year→ Month→ Day→ Temperature format C/F→ Exit

2.2 Alarm Setting

To turn on alarm press the "ALARM"(1d) button once. The alarm icon will appear above the time and the last alarm setting will appear.
Press and hold "ALARM"(1d) Button for 2 seconds and the first digit of the setting will start to Flash.
Setting item blinking at 1s frequency.
Press "UP"(1b) key, the value goes ahead one step; press and hold for 2 seconds, go ahead at an 8 step per second speed.
Press "DOWN"(1c) once and back; press and hold for 2 seconds, go back at an 8 step per second speed.
After setting, press "ALARM"(1d) to confirm and exit.
After 10 seconds of not pressing any button, the device will exit the change mode and will save all current settings that were changed to that point.
AL2 Setting is the same as the AL1 setting.
Setting in sequence: Alarm Hour→Alarm Minute →Exit

2.3 Alarm ON/OFF

When the alarm turns on you can press. "ALARM"(1d) button to shut it off. You can also press the "Snooze"(1f) button. It will turn off again after the
*Snooze* time runs out after 5 minutes.
After 2 minutes of working the alarm will shut down of its own accord.
To change the backlight strength press "SNOOZE/LIGHT"(1f) once. The device has 2 settings. 1. Maximum backlight 2. Minimum backlight.
You can turn on the snooze function without limit.
* Snooze could be repeated all the time.
The alarm has 3 settings.
a.0-10 seconds after the alarm starts, the device will make a noise 1 time per second
b.10-20 seconds after the alarm starts, the device will make a noise 2 time per second
c. Over 20 seconds after the alarm starts, the device will make a noise 4 time per second
2.5 Temperature and Humidity Function
* Out of the indoor and outdoor temperature display, the low-end displays "Lo", the high-end displays "Hi". You can check the lowest and highest recorded
temperatures by pressing the „Max/Min" briefly to cycle between them.
* Indoor temperature upper limit: 50C, lowest limit: 0C.
* Outdoor temperature upper limit: 70C, lowest limit: -40C.
2.4 Date check
To check the Date. In default mode, press the „Mode"(1a) button once.
2.5 Alarm time check.
To check the Alarm setting. In default mode, press the „Mode"(1a) button twice.
TECHNICAL DATA
Supply voltage - Station: AC 100-240 V 50 / 60Hz plus 3 1.5V AAA batteries
Supply voltage - Probe: 2 1.5V AAA batteries. Frequency: 433.99 MHz Power: 0,115 mW
Adler Sp. z o.o. Ordona 2a, 01-237 Warsaw, Poland hereby declares that the AD1176 device complies with the Directive
2014/53 / EU. The full text of the EU declaration of conformity is available at the following internet address:
https://adler.com.pl/dane/CE/ADLER/AD1176.pdf
4