Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

GROOVED COUPLING ADAPTER
INSTALLATION INSTRUCTIONS
READ THESE INSTRUCTIONS CAREFULLY BEFORE BEGINNING
INSTALLATION
The following procedures are recommended for proper assembly of the
Grooved Coupling Adapter.
INSTALLATION PROCEDURES
STEP 1
Inspect the fi ttings and pipe to insure that they are suffi ciently
free from indentations, projections or roll-marks on the gasket seating
areas of the fi tting and pipe. The pipe should be squarely cut. Any loose
scale, paint and/or dirt must be removed from the groove and sealing
surfaces. Use a gasket material suitable for the intended application as
recommended by the coupling manufacturer.
STEP 2
Make sure that the gasket is clean and free of any cracks,
cuts or other defects which may cause leaks. DO NOT allow solvent
cement or primer to contact gasket sealing surface or the gasket, as leaks
may develop. A gasket/joint lubricant is recommended to prevent pinching
the gasket and to assist the seating and alignment processes. Apply a thin
layer of appropriate lubricant to the gasket lips and exterior surface of the
gasket. Caution: Certain lubricants can contain a petroleum base or other
chemicals which may cause damage to the gasket and adapter. It is the
installers responsibility to verify suitability for use of the selected lubricant
with the manufacturer.
PVC & CPVC SCHEDULE 80
Spears
®
Adapters were designed
using the Victaulic style 75
and 77 fl exible coupling.
Other couplings of similar
fl exible design may
used. CAUTION: Use of
rigid style couplings may
damage
coupling adapter. Consult
the coupling manufacturer
for proper selection.
1
GCA-3A-0407
Grooved Coupling
be
the
grooved

Publicidad

loading

Resumen de contenidos para Spears PVC

  • Página 1 PVC & CPVC SCHEDULE 80 GROOVED COUPLING ADAPTER INSTALLATION INSTRUCTIONS GCA-3A-0407 Spears Grooved Coupling ® Adapters were designed using the Victaulic style 75 and 77 fl exible coupling. Other couplings of similar fl exible design may used. CAUTION: Use of...
  • Página 2 Position the gasket onto the pipe, making sure that the gasket STEP 3 lip does not overhang the end of the pipe. Align the grooved coupling adapter with the end of the pipe. Slide the gasket over the seating surface of the adapter, centering the gasket between the two grooves.
  • Página 3 MANUFACTURING COMPANY ® CORPORATE OFFICE 15853 Olden Street, Sylmar, CA 91342 PO Box 9203, Sylmar, CA 91392 (818) 364-1611 • www.spearsmfg.com © Copyright 2007 Spears Manufacturing Company. All Rights Reserved. ® Printed in the United States of America 04/07. GCA-3A-0407...
  • Página 4 ADAPTADOR DE ACOPLAMIENTO DE RANURA DE PVC Y CPVC CÉDULA 80 INSTRUCCIONES DE INSTALACIÓN GCA-3A-0407 Los adaptadores de acoplamiento de ranura de Spears fueron ® diseñados utilizando los acopladores fl exibles estilo 75 y 77 de Victaulic. Otros acopladores diseño fl...
  • Página 5 3er. PASO Posicione el empaque en la tubería, asegurándose de que el labio del empaque no cuelgue del extremo de la tubería. Alinee el adaptador de acoplamiento ranura con el extremo de la tubería. Deslice el empaque sobre el área de asiento del adaptador, centrando el empaque entre las dos ranuras.
  • Página 6 MANUFACTURING COMPANY ® CORPORATE OFFICE 15853 Olden Street, Sylmar, CA 91342 PO Box 9203, Sylmar, CA 91392 (818) 364-1611 • www.spearsmfg.com © Copyright 2007 Spears Manufacturing Company. All Rights Reserved. ® Printed in the United States of America 04/07. GCA-3A-0407...

Este manual también es adecuado para:

Cpvc