IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
Read all instructions before using this Heater.
WARNING
• PLUG HEATERS DIRECTLY INTO A 120V WALL OUTLET/RECEPTACLE ONLY. NEVER USE WITH AN EXTENSION CORD. DO NOT
PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR, MULTIPLE OUTLET
ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE A FIRE HAZARD. DO NOT
PLUG MULTIPLE DEVICES IN THE SAME OUTLET OR ON SAME CIRCUIT AS HEATER.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG FITS
TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS NOT OVERHEATING.
IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO NOT USE THIS HEATER
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left operating unattended.
Never leave children unattended when the heater is on or plugged in.
• The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circum-
stances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be replaced
with a properly grounded three-prong receptacle, installed in accordance with the National Electrical Code (NEC) and all applicable
local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
• USE OF A THREE-PRONG TO TWO-PRONG ADAPTER IS NOT RECOMMENDED. IMPROPER CONNECTION MAY CREATE THE
RISK OF ELECTRIC SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations where
flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any manner.
To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings may become blocked.
Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the heater. Always unplug
the power cord.
CAUTION
• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners,
or similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep com-
bustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
• DO NOT use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer to
National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for Agricul-
tural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local
codes or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS
OF NEC ARTICLE 500 (2008).
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
SAVE THESE INSTRUCTIONS
NEW 3/15
WARNING
2
El calor impulsado por el ventilador es
distribuido a nivel del piso para que el calor
envolvente comience a sus pies.
Aire de
Habitación
Aire
Calentado
FUNCIONAMIENTO
1. Cuidadosamente retire el Calefactor de la bolsa y la caja.
2. Coloque el Calefactor sobre una superficie firme y nivelada.
CUIDADO:
Los tacos de plástico o hule, tales como las patas
de esta unidad, pueden pegarse a la superficie de los muebles y/o
a los pisos de madera. La unidad podría dejar un residuo capaz de
oscurecer, manchar o dejar marcas permanentes en el acabado de
ciertas superficies de muebles, incluyendo superficies de madera
y/o pisos de madera.
3. Asegúrese que el Interruptor de Encendido esté en la posición
APAGADO oprimiendo (0). (Figura 1)
4. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes
en este estado podrían sobrecalentarse y representar
un peligro de incendio grave; si queda cubierto por
una cortina o tela, el peligro de incendio es todavía
mayor.
5. Para ENCENDER el Calefactor oprima el Interruptor de
Encendido a (l). La luz del interruptor se encenderá.
6. Cuando el Interruptor de Encendido está ENCENDIDO,
el Calefactor liberará calor constantemente hasta que el
Interruptor de Encendido sea APAGADO.
7. Para APAGAR el Calefactor oprima el Interruptor de Encendido
a (o) y desconecte el Calefactor del tomacorriente eléctrico.
8. Cuando se lo encienda por primera vez, el Calefactor estará en
calor Alto (1500 vatios).
WC14812ES
NEW 3/15
MODELO WC14812
Perilla del Termostato Regulante
Interruptor de
Figura 1
Encendido
FUNCIONAMIENTO DEL TERMOSTATO
REGULANTE
1. Coloque la Perilla del Termostato Regulante en la posición
deseada ( ). Antes de ajustar el termostato regulante, deje que
el Calefactor funcione y caliente la habitación.
2. Cuando se haya logrado el nivel de comodidad a la temperatura
deseada, baje la posición del termostato hasta que oiga un "clic".
Esto se hace moviendo la Perilla del Termostato Regulante
hacia la posición Bajo (
). El termostato regulante ahora
quedará ajustado en la posición baja.
3. Es normal que el Calefactor oscile entre un vataje alto y bajo
mientras mantiene la temperatura ambiente. NOTA: El motor
del ventilador no cambia cuando el calefactor está alternando
entre calor alto y bajo. Cuando el Interruptor de Encendido
está ENCENDIDO (iluminado), el Calefactor está constantemente
energizado para liberar aire calentado. Para APAGAR el
Calefactor oprima el (o) en el Interruptor de Encendido.
(Figura 1)
7
WC14812ES