Assembly; Preparation; Making Ice Cream - Silvercrest SECM 12 B2 Instrucciones De Uso

assembly

Use the diagrams on the fold-out page as a guide
for assembly!
1) Remove all packaging materials and any
stickers from the appliance .
2) Clean the appliance as described in the
section "Cleaning and Care" .
3) Place the base 0 on a flat surface .
4) Insert the drive shaft 6 into the corresponding
recess on the ice scraper 7 until the ice
scraper 7 clicks into place .
5) Insert the other end of the drive shaft 6 into
the corresponding drive shaft socket 3 .
6) Put the lid 5 on the freezer bowl 9 . Ensure
that the symbol on the lid 5 points at the
symbol on the freezer bowl 9 . Turn the lid 5
clockwise until it clicks into place . The
on the lid 5 points at the
freezer bowl 9 .
7) Insert the plug into a mains power socket .
The appliance is now ready for use .

Preparation

♦ Place the freezer bowl 9 in the deep freeze
for about 24 hours at a temperature of no more
than -18°C .
Tips
► Keep the freezer bowl 9 upright in the
freezer .
► Ensure that the beakers 9 are completely
dry before you place them in the freezer .
► Store the fruit, milk and cream in the refrigera-
tor before processing . This ensures that the
fruit is already cold and thus the ice cream
mixture will not require so long to cool down .
► Place a plastic bag, for instance a freezer
bag, in the freezer bowl 9 before freezing .
♦ Puree the fruit with a hand blender and mix all
the ingredients as described in the recipe .
♦ Allow the mixture to cool down for approx .
4 hours .
SECM 12 B2
All manuals and user guides at all-guides.com
symbol
symbol on the

making ice cream

caUTIoN! PRoPERTy DamaGE!
► Start the appliance first and then add ingre-
dients . Otherwise, the ice mixture will freeze
onto the sides of the freezer bowl 9 and
block the ice scraper 7 . This will cause the
motor to overheat!
► Do not stop the appliance during processing!
Otherwise, the ice mixture will freeze onto
the sides of the freezer bowl 9 and the ice
scraper 7 will be blocked when you switch
the appliance back on . This will cause the
motor to overheat!
1) Remove the freezer bowl 9 from the freezer
and place it in the base .
2) Assemble the appliance as described in the
chapter titled "Assembly" .
3) Switch the appliance on by moving the On/
Off switch 1 to the position I . The whisk 7
starts to turn .
4) Now, fill the prepared ice mixture into the
freezer bowl 9 through the filling opening 4 .
Ideally, use a bowl with a spout . Never add
more than 1000 ml . During processing, the
mixture increases in volume!
5) Allow the appliance to continue running until
you are satisfied with the consistency of the
mixture . The ice cream is ready after 40 min-
utes at the most .
6) Switch the appliance off at the On/Off switch
1 and pull the mains power plug out of the
socket .
7) Turn the lid 5 until you can take it off .
8) Pull the ice scraper 7 out of the ice cream .
If the ice cream sticks to it, scrape it off with a
plastic spoon or similar tool .
9) Lift the freezer bowl 9 out of the appliance
and remove the ice cream . Use only plastic or
wooden implements to do this .
caUTIoN! PRoPERTy DamaGE!
► Do not use metal utensils to remove the ice
cream from the freezer bowl 9 . They can
scratch the freezer bowl 9 .
GB │ IE │ 15 ■