Husqvarna R 147 Manual Del Usuario página 11

ENGLAND
(starts at page 55)
O O O O O
Keep the engine stop lever (14) depressed during machine
operation. When the lever is released, the engine stops.
P P P P P
(starts at page 56)
Keep the engine stop lever (14) depressed during machine operation. When the lever is
released, the engine stops.
MOWING
To cut the grass, push the lawn mower manually or insert the automatic advance gear.
(starts at page 56)
Q Q Q Q Q
Motor start up
LOADING THE TOUCH-N-MOW SYSTEM
To load the start up system for the first time and whenever the device is disabled,
proceed as follows:
(starts at page 56)
R R R R R
Press the pump (Primer) (2) 3 or 4 times.
1 - Act on the safety lever (14) and keep it pressed against the handgrip.
2 - Push the Touch-N-Mow start up lever forward (16).
(starts at page 56)
M
S S S S S
Start up the motor by holding the engine start grip (11) and pulling it effortlessly
until reaching the resistance caused by compression, release the handle and
pull vigorously. If necessary, repeat the operation if the motor does not start.
(starts at page 56)
T T T T T
To engage the automatic drive, act on the clutch handle (18) and keep it pressed
against the handgrip.
Caution:engage only with operating motor .
(starts at page 56)
U U U U U
After switching off, take the Touch-N-Mow key (17) to LOCK & REMOVE position
to lock the system.
Remove the key from upwards.
Caution: Without the Touch-N-Mow key in RUN position or with the key in LOCK & REMOVE position, the motor will not start!
START UP WITH TOUCH-N-MOW
Make sure that no person or object is near the machine and all protection devices are
installed and operating.
Remain behind the handgrip in the position required for use.
- Insert the key (17) and rotate it to RUN position.
- Act on the safety lever (14) ) and keep it pressed against the handgrip.
- Push the Touch-N-Mow start lever (16) forward and check the motor start up.
UNLOADING THE TOUCH-N-MOW SYSTEM
Prior to any cleaning or transport operation, the start up system shall be unloaded.
For this operation, proceed as follows:
- Disconnect the spark plug cable.
- Act on the safety lever (14) ) and keep it pressed against the handgrip.
(starts at page 56)
V V V V V
Important: If, when you press the clutch lever, the automatic advance gear does not engage, the clutch cable should be adjusted by inserting the spring (P) in one of the
subsequent holes in the plate (R) (or in the hole "S" .
AUTOMATIC ADVANCEMENT
W W W W W
Periodically check the automatic advance assembly and make sure to keep it clean. In particular, the pinion (20) and the gear (21) must be kept perfectly clean. To carry
out this check, you must remove the wheel (22) by unscrewing the screw (23).
(starts at page 56)
MOWING
To cut the grass, push the lawn mower manually
How to insert automatic advance: Lift up the clutch handle (18) and keep it pressed in
position.
CAUTION: Engage the gear only when the engine is running.
How to disengage advance: Release the clutch handle.
1 - Insert the Touch-N-Mow key (17) (provided with the machine)
2 - Rotate the key (17) to "RUN" position
- Keep the safety lever (14) pressed during operation; if released, the motor will stop.
CUT
To cut the grass, manually push the machine or engage the automatic drive.
To disengage the automatic drive, release the clutch handle (18).
After the cut, first release the clutch handle (18) then the safety lever (14) and a noise
caused by the reloading of the Touch-N-Mow system will be heard.
After cutting the grass, always remove the key and store it in a safe place available to the
authorized operators only.
Caution: if the motor does not start, it means that the Touch-N-Mow start up system has
been unloaded. If so, proceed to load it as described in the relevant section.
Important: Should the motor stop due to lack of gasoline, excessively high grass, or any
reason other than the normal stop procedures, the Touch-N-Mow start up system will not
reload and it will be necessary to repeat the previously described operations in order to
load the system.
- Push the Touch-N-Mow lever (16) forward.
- The motor will run but it will not start as the spark plug cable is disconnected.
- Turn the Touch-N-Mow key (17) to LOCK & REMOVE position.
- Remove the key (17).
10