Trevi ME 3108 RC Manual De Instrucciones página 6

Ocultar thumbs Ver también para ME 3108 RC:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

ME 3108 RC
speed.
-
Without any effect handling more than 8
seconds, it returns from setting automatically.
-
Finish setting, alert is on.
3.0 Open or reset
-
The LCD display fully is for 3 seconds when
changing new battery or resetting, then with
a sound BI into the normal state, testing
temperature and humidity, after receiving RF
for 3 minutes no matter receive or not, it will
exit after 7 minutes.
3.1 RF receiving function
-
Receiving RF for 3 minutes automatically
after testing temperature and humidity when
assembled battery.
-
Press "CHANNEL" for 2 seconds to cancel the
register of present channel.
-
When the registered CH temperature haven't
received effect symbol in the same ID code
in 60 minutes, the CH will be display "--.-".
Then start to receive for 3 minutes.
-
The Synchronizing cycle is CH1=57S,
CH2=67S, CH3=79S.
-
Priority: When RF meets RCC, RCC receiving
first and then RF receiving; When alarm meets
RCC, alarms first, then RCC receiving, finally
RF receiving.
3.2 RCC receiving
-
RCC receiving controlling:
1. When start or re-set, automatically receive
RCC after 3 minutes.
2. Press "DOWN" 2 seconds to RCC receiving
by force.
3. Automatically receive every day
-
A u t o m a t i c a l l y r e c e i v i n g t i m e : A t
1:00,2:00,3:00,4:00,5:00 am. each day, au-
tomatically enter RCC receiving. Meanwhile, at
1:00, 2:00, 3:00 must be receiving. If it fails in
receiving at 3:00, it will continue to receive at
4:00, 5:00, if it received successfully at 4:00,
it will not receive again that day. Otherwise it
will continue to receive at 5:00, whatever it
receives successfully or not at 5:00, it will
be no longer receiving, receiving RCC (up to)
DCF time is 7 minutes.
-
RCC receiving icon
1. If entered RCC receiving, the RCC symbol will
be blinking at the frequency of 1HZ.
2. If received the signal, the RCC symbol will be
static and the arc figure will be blinking at the
frequency of 1 HZ.
3. If the signal is weak and hard to find out the
correct signal, the symbol will be blinking at
the frequency of 1HZ, then the arc figure will
disappear.
4. If the symbol is received successfully, its
symbol will be full displayed and exit receiving
state.
-
If it is on receiving rcc, press "DOWN" 2 seconds
to exit receiving, and press "SNZ/LIGHT" to light
and no function to press other key.
-
If it fails received on that day, receiving rcc
again would be 1:00 am at the next day
-
If it meets alarms, it will exit RCC receiving
and enter into alarm under receiving RCC.
-
When received the DST icon, it will be displa-
yed on the LCD.
-
When RCC symbol is displayed, RCC symbol
will disappear after resetting the time.
3.3 Alarm setting
-
When it alarms, press "SNZ/LIGHT" to start
snooze and exit with any other keys.
3.5 Weather forecast
-
Weather forecast is for the next 24H.
-
W e a t h e r f o r e c a s t : S u n n y > S e m i -
sunny>Cloudy>Rainy
-
Forecast should be accurate under the normal
and ventilated condition, and it will occur the
deviation when at indoor or in air-conditioned
environment.
3.6 Temperature alert:
-
Default value of temperature alert is +70°C
highest and -50°C lowest.
-
The relevant temperature and alert symbol will
be twinkling if it alerts.
-
It will be only display alert symbol twinkling
not temperature display if the temperature
alert is not for present Channel.
-
Alert Sound:
a. BI BI BI per second;
6
English

Publicidad

Tabla de contenido
loading

Tabla de contenido