Publicidad
Idiomas disponibles
Idiomas disponibles
1 Operating instruction cable set Poolmax TP25/35/50/75/120/150
Ubbink Poolmax TP-pumps are supplied with a plug with earth leakage circuit breaker (FI) as standard. The power supply cable must be replaced for the operation of the
Ubbink Poolmax TP-pumps are supplied with a plug with earth leakage circuit breaker (FI) as standard. The power supply cable must be replaced for the operation of the
pump via the power plug of a time switch clock or a switch box with time switch clock with power plug. Please, read these operating instructions thoroughly and keep them
pump via the power plug of a time switch clock or a switch box with time switch clock with power plug. Please, read these operating instructions thoroughly and keep them
for correct replacement of the power supply cable.
for correct replacement of the power supply cable.
Article number
Cable length
Cable type
Power plug
Safety instructions
Safety instructions
• The replacement of the power supply cable at the Poolmax TP pump must be carried out exclusively by an approved electrician.
• The cross section dimension of the power supply cable must not be reduced. The cable must be at least of the type H05RN-F 3*0.75 mm
mm
for Poolmax TP75/TP120/TP150.
2
• The power supply of the device must be carried out via an earth leakage circuit breaker (FI-switch) with < 30 mA nominal fault current in accordance with the European safety
standards.
• Do not cut o the safety plug with earthing from the power supply cable and also do not shorten the power supply cable of the device. The guarantee becomes invalid if this is not
observed.
• If the power supply cable or the power plug is damaged, the device must be taken out of operation immediately to avoid any danger.
Replacement of the power supply cable
Replacement of the power supply cable
• Separate the pump from the power supply
• Open the cover of the control box (Figure 1) on the pump
• Take o the connection of the 3 power supply wires (Figure 2)
• Loosen the inner and outer cable locking xture (Figures 3 +4)
• Carefully pull out the power supply cable from the cable bushing (Figure 5)
• Insert the power supply cable of the cable set (Figure 6)
• Fasten the inner and outer cable locking xture (Figures 7 +8)
• Connect the 3-wire power supply cable (Figure 9)
Brown/black= Live wire
Blue = Neutral wire
Green-yellow = Protective wire
• Insert the seal and close the control box with the cover (Figure 10)
• The pump is now ready for operation via time switch clock or switch box with time switch clock.
Guarantee
Guarantee
The guarantee for your Poolmax TP-pump does not become invalid under the precondition that the replacement of the power supply cable and other maintenance work has been
The guarantee for your Poolmax TP-pump does not become invalid under the precondition that the replacement of the power supply cable and other maintenance work has been
carried out provably by an approved specialist electrical company.
Correct disposal of this product
This symbol points out inside the EU that this product must not be disposed via domestic waste. Old devices contain valuable materials for recycling, which should
be passed on to recycling and not harm the environment or human health due to uncontrolled waste disposal. Please, dispose the old devices therefore via suitable
collecting systems or send the device for disposal to the place you bought it from. This will then pass on the device to recycling.
Manual Poolmax - Kabelset.indd 5
manual poolmax cable.indd 5
Cable set Poolmax TP25/35/50
7534149
1.5 m
H05RN-F 3*0.75mm
2
Hybrid E&F (HL-28 Rainproof)
Cable set Poolmax TP75/120/150
7534150
1,5 m
H05RN-F 3*1.00mm
2
Hybrid E&F (HL-28 Rainproof)
for Poolmax TP25/35/50 and H05RN-F 3*1.00
2
23.09.13 17:10
19-10-12 11:20
Publicidad
