Milwaukee Rover M12 Guia De Inicio Rapido

IMPORTANT SAFETY
INSTRUCTIONS
READ AND UNDERSTAND ALL IN-
WARNING
STRUCTIONS. When using electric
appliances, basic precuautions should always be
followed, including the following:
Before using the flood light, read this operator's
manual, your battery pack and charger operator's
manual, and all labels on the battery pack, charger
and flood light.
• Read and understand all the instructions before
using the appliance.
• Do not use magnet for horizontal overhead mounting.
•To reduce the risk of electric shock, do not put light
in water or other liquid. Do not place or store appliance
where it can fall or be pulled into a tub or sink.
• Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to battery pack,
picking up or carrying the appliance. Carrying the
appliance with your finger on the switch or energizing
appliance that have the switch on invites accidents.
• Disconnect the battery pack from the appliance
before making any adjustments, changing acces-
sories, or storing appliance. Such preventive safety
measures reduce the risk of starting the appliance
accidentally.
• To reduce the risk of injury, close supervision is
necessary when an appliance is used near children.
• Store idle flood light out of reach of children. Warm
flood lights can become hazardous in the hands of
children.
• Do not use outdoors.
• For a rechargeable appliance - Use only the charger
supplied by the manufacturer to recharge.
• Know your flood light. Read this manual carefully to
learn your flood light's applications and limitations as
well as potential hazards associated with this type of
tool.
• Batteries must be recharged only with the charger
specified by the manufacturer. A charger that may
be suitable for one type of battery may create a risk of
fire when used with another battery.
• Use flood light only with specifically designated
battery pack. Use of any other batteries may create a
risk of fire.
• When battery pack is not in use, keep it away from
metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
the battery terminals together may cause sparks, burns,
or a fire.
• Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
Cat. No. ....................................................... 2367-20
Volts ................................................................. 12 DC
Battery Type ....................................................M12™
Charger Type...................................................M12™
USB Ouput .....................................................5 V DC
USB Amps ............................................................ 2.1
Recommended Ambient
Operating Temperature .........................0°F to 125°F
SYMBOLOGY
Do not stare at the
Volts
operating light source
Direct
Current
UL Listing for Canada
and U.S.
Amps C US
LIGHT
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Inserting/Removing Battery Pack
Insert the battery pack by sliding battery pack into
the body of the tool. Insert the battery pack until the
battery latches lock.
To remove the battery pack, press in both battery
latches and slide the battery pack off of the tool.
Power
To reduce the risk of injury, do not
CAUTION
stare at the operating light source.
Press the power button to cycle through HIGH,
LOW, and OFF settings.
USB Port
To charge a phone or other electronic device using the
2.1A USB port, plug in the USB and press the USB
wake button. The port will remain ON for about 2 hours.
13135 West Lisbon Road • Brookfield, Wisconsin, U.S.A. 53005
58222367d1 08/20
M12™
W/ USB CHARGING
PROJECTEUR POUR RÉPARATIONS ET SERVICES À
CHARGEMENT PAR USB M12™
LÁMPARA TIPO REFLECTOR DE SERVICIO Y REPARACIÓN
CON CARGA MEDIANTE USB M12™
MAINTENANCE
WARNING
battery pack from the charger or tool before per-
forming any maintenance. Never disassemble the
tool, battery pack or charger. Contact a MILWAUKEE
service facility for ALL repairs.
Keep your light, battery pack and charger in good
repair by adopting a regular maintenance program. If
the light does not work properly, return the light to a
MILWAUKEE service facility for repairs.
WARNING
tool, battery pack or charger in liquid or allow a
liquid to flow inside them.
Keep tool handles clean, dry and free of oil or grease.
Use only mild soap and a damp cloth to clean the tool,
battery pack and charger since certain cleaning agents
and solvents are harmful to plastics and other insulated
parts. Some of these include gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning
solvents, ammonia and household detergents contain-
ing ammonia. Never use flammable or combustible
solvents around tools.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair or
replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship
for a period of five (5) years** after the date of purchase unless otherwise
noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and
insured, is required. A copy of the proof of purchase should be included
with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by
anyone other than MILWAUKEE authorized personnel, misuse, altera-
tions, abuse, normal wear and tear, lack of maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover
repair when normal use has exhausted the life of a part including,
but not limited to, chucks, brushes, cords, saw shoes, blade clamps,
o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and
bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint
Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power
Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain; M12™
Heated Gear; Reconditioned Product; and Test & Measurement Products.
There are separate and distinct warranties available for these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is
one (1) year from the date of purchase. The warranty period for the M18
FUEL™ 1" D-Handle High Torque Impact Wrenches, Drain Cleaning
Cables, AIRSNAKE™ Drain Cleaning Air Gun Accessories, and RED-
LITHIUM™ USB Laser Levels is two (2) years from the date of purchase.
The warranty period for the M18™ Compact Heat Gun, 8 Gallon Dust
Extractor, M18™ Framing Nailers, M18 FUEL™ 1/2" Ext. Anvil Controlled
Torque Impact Wrench w/ ONE-KEY™, M18 FUEL™ 1" High Torque
Impact Wrench w/ ONE-KEY™, M18 FUEL™ 2 Gal. Compact Quiet
Compressor, and M12™ Laser Levels is three (3) years from the date
of purchase. The warranty period for the LED in the LED Work Light and
the LED Upgrade Bulb for the Work Light is the lifetime of the product
subject to the limitations above. If during normal use the LED or LED
Bulb fails, the part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable war-
ranty on a MILWAUKEE power tool product. The manufacturing date of
the product will be used to determine the warranty period if no proof of
purchase is provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CON-
TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF
YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT PUR-
CHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE
FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE
DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES, EXPENSES,
LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF
ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF
PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT
PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WAR-
RANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WAR-
RANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT
PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED
TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS
DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the 'Service Center Search' in the Parts & Service sec-
tion of MILWAUKEE's website www.milwaukeetool.com or call 1.800.
SAWDUST (1.800.729.3878) to locate your nearest service facility for
warranty and non-warranty service on a Milwaukee electric power tool.
MILWAUKEE TOOL
Printed in China 01614600101Q-01(A)
SERVICE & REPAIR FLOOD LIGHT
To reduce the risk of injury, always
unplug the charger and remove the
Maintain Light
To reduce the risk of personal injury
and damage, never immerse your
Cleaning
(1.800.729.3878)
www.milwaukeetool.com
1.800.268.4015
INSTRUCTIONS DE
SÉCURITÉ IMPORTANTES
VOUS DEVEZ LIRE ET
AVERTISSEMENT
COMPRENDRE TOUTES
LES INSTRUCTIONS. Lors de l'utilisation d'outils
électriques, toujours suivre les consignes de base,
notamment:
Avant d'utiliser l'éclairage par projection, lire le
présent manuel d'utilisation et celui du bloc-piles et du
chargeur, ainsi que toutes les étiquettes se trouvant sur
le bloc-piles, le chargeur et l'éclairage par projection.
• Lire et bien comprendre toutes les instructions
avant d'utiliser l'appareil.
• N'utilisez pas d'aimant pour le montage horizontal.
• Pour réduire le risque de choc électrique, ne pas
submerger la lampe dans l'eau ou tout autre liquide.
Ne pas placer ni entreposer l'appareil dans un endroit où
il peut tomber ou être tiré dans un évier ou une baignoire.
• Empêcher les démarrages accidentels. S'assurer
que la gâchette en position d'arrêt avant de d'insérer
batterie, de le ramasser ou de le transporter. Le fait
de transporter de l'appareil en gardant le doigt sur la gâ-
chette ou de mettre sous tension un l'appareil lorsque la
gâchette est en position de marche favorise les accidents.
• Déconnectez le bloc-piles de l'appareil avant
d'effectuer des réglages, de changer d'accessoire ou
ranger l'appareil. Ces mesures de sécurité préventives
réduisent les risques de démarrage accidentel l'appareil.
• Pour réduire les risques de blessures, porter une
attention particulière lorsque le produit est utilisé en
présence d'enfants.
•Entreposer l'éclairage par projection non utilisé
hors de la portée des enfants. Les éclairages par
projection chauds peuvent être dangereux dans les
mains des enfants.
• Ne pas utiliser cet outil à l'extérieur.
• S'il s'agit d'un outil rechargeable, utiliser exclu-
sivement le chargeur fourni par le fabricant afin de le
recharger.
•Savoir votre éclairage par projection. Lire attentive-
ment ce manuel pour apprendre les applications et les
limites de votre éclairage par projection, ainsi que les
risques spécifiques relatifs à son utilisation.
• Doit être rechargée seulement avec le chargeur
spécifié pour la pile. Un chargeur adapté à un certain
type de pile peut créer un risque d'incendie s'il est utilisé
avec d'autres piles.
•N'utiliser l'éclairage par projection qu'avec le bloc-
piles recommandé. L'usage de toutes autres piles
peut créer un risque d'incendie.
• Lorsque le bloc-batterie n'est pas en service,
tenez-le à l'écart d'autres objets métalliques (trom-
bones, pièces de monnaie, clés, clous, vis, etc.)
susceptibles d'établir un contact électrique entre
les deux bornes. La mise en court-circuit des bornes
de la batterie peut produire des étincelles et constitue
un risque de brûlures ou d'incendie.
• Entretenez les étiquettes et marques du fabricant.
Les indications qu'elles contiennent sont précieuses.
Si elles deviennent illisibles ou se détachent, faites-
les remplacer gratuitement à un centre de service
MILWAUKEE accrédité.
CONSERVEZ CES INSTRUCTIONS
SPÉCIFICATIONS
No de Cat.. .................................................. 2367-20
Volts ................................................................. 12 CD
Type de batterie ..............................................M12™
Type de chargeur ...........................................M12™
Sortie USB ......................................................5 V CD
Ampéres USB ....................................................... 2,1
Température ambiante de fonctionnement
recommandée ..............-18°C à 50°C (0°F à 125°F)
PICTOGRAPHIE
Ne pas regarder la
Volts
source de lumière
de fonctionnement
Courant
direct
UL Listing Mark pour
Ampères
Canada et États-unis
C US
PROJECTEUR
Ne recharger la batterie
AVERTISSEMENT
qu'avec le chargeur spéci-
fié. Pour les instructions de charge spécifiques,
lire le manuel d'utilisation fourni avec le chargeur
et les batteries.
Insertion du bloc de piles dans l'outil
Insérez le bloc de piles à partir de l'avant en le faisant
glisser dans le corps de l'outil. Insérez le bloc de piles
jusqu'à ce que son loquet se verrouille.
Pour retirer le bloc de piles, enfoncez les deux loquets
de la pile et faites glisser le bloc hors de l'outil.
Alimentation
Afin de réduire le risque de bles-
PRÉCAUTION
sure, ne pas regarder la source
de lumière de fonctionnement.
Appuyer sur le bouton d'alimentation et le tenir
enfoncé pour naviguer entre les paramètres HAUT,
FAIBLE et ARRÊT.
Port USB
Pour charger un téléphone ou un autre dispositif élec-
tronique en utilisant le port USB, le bran cher dans le
USB et appuyer sur le bouton d'alimentation. Le port
restera ON pendant environ 2 heures.