Maintenance Instructions - Hoover BH90100 Manual Del Usuario

OPERATION
WARNING:
Risk of fire or explosion. Spray area must be well ventilated and
away from sparks or flames.
WARNING:
DO NOT use on or near electronic devices.
Using Your Sprayer
DANGER:
Improper application of cleaning solution can result in SEVERE
INJURY or DEATH. Follow CDC and EPA guidelines for cleaning. Follow the chemical
manufacturer's safety instructions and guidelines listed on the SDS sheet.
1. Install the battery pack.
2. Direct the sprayer nozzle directly at the surface areas you wish to treat.
NOTE: Make sure to stand far enough from the object being sprayed to prevent the spray
from splashing back onto you.
3. Squeeze and hold the switch trigger while the unit primes. This may take several
seconds. Continue holding the trigger until unit begins to spray.
4. Spray on a dry surface using long, even, overlapping strokes.
NOTE: While the sprayer is in use some dripping from the nozzle may occur, this is to be
expected.
5. Release the switch trigger to stop the spray.
6. When you are finished with the sprayer, remove the battery pack.
7. Remove the tank and unscrew the cap.
8. Return any unused fluid to its original container, and thoroughly clean the sprayer.
9. Thoroughly clean the sprayer and tank before transporting or storing the unit and
before switching to a different chemical. See Cleaning the Unit later in this manual.
NOTE: Make sure to stand far enough from the object being sprayed to prevent the spray
from splashing back onto you.
10. Thoroughly wash your hands and any area where skin has been exposed to the spray.
A
A. Switch Trigger
Safety Guidelines
• Never point the spray end of the sprayer at yourself or others.
• Avoid spraying on windy days. Mist can be accidentally blown onto plants or objects
that should not be sprayed.
• Never point sprayer in the direction of people or animals; always direct downwind.
• Especially in warmer weather, use sprayer in the early morning or late afternoon.
Excessive heat can evaporate the mist before it settles.
• Never smoke, eat, or drink while operating the sprayer.
• Do not touch nozzles when sprayer is in operation.

MAINTENANCE INSTRUCTIONS

If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped
into water, call customer service, ONEPWR Support 1-800-406-2005 prior to continuing use.
This product contains no serviceable parts. Call ONEPWR Support 1-800-406-2005 for
Customer Service.
WARNING:
To avoid serious personal injury, always remove the battery pack
from the tool when cleaning or performing any maintenance.
WARNING:
Always wear eye protection with side shields or goggles marked to
comply with ANSI Z87.1. Failure to do so could result in fluids entering your eyes
resulting in possible serious injury.
WARNING:
When servicing, use only identical replacement parts. Use of any
other parts may create a hazard or cause product damage.
NOTICE: Periodically inspect the entire product for damaged, missing, or loose parts
such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts are replaced. Please contact
customer service or an authorized service center for assistance.
General Maintenance
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage
from various types of commercial solvents and may be damaged by their use. Use clean cloths
to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic
which may result in serious personal injury.
After Care and Cleaning
If there is any liquid left in the tank after spraying, the tank should be drained before cleaning.
1. Remove the battery pack.
2. Remove the tank and unscrew the cap.
3. Drain the contents of the tank through the fill area.
NOTE: Drain the contents back into the original container. Do not store chemicals in the tank.
WARNING:
Always store and dispose of chemicals properly. Disposal of
contaminated rinse water should be performed according to local ordinances and
bylaws. Draining the tank: If there is any liquid left in the tank after spraying, the tank
should be drained before cleaning.
CLEANING THE TANK AND SPRAY LINES:
1. Using a faucet, flush debris out of the filter located at the bottom of the cap assembly.
2. Fill the tank about one-third full with clean water. A small amount of mild household
detergent may be added.
NOTE: Drain the contents back into the original container. Do not store chemicals in the tank.
3. Wipe the outside of the tank with a clean, dry cloth.
4. Replace the cap.
5. Reinstall the tank and latch to secure.
6. Reinstall the battery pack. Spray until the tank has been emptied. Make sure to direct
the spray toward an area that will not be damaged by the spray solution.
7. Refill and repeat the procedure with clean water. It may be necessary to rinse the tank
more than once, then drain again as directed above.
8. Allow all pieces to completely dry before reinstalling parts and storing the unit.
IMPORTANT: Store the sprayer in an upright position. DO NOT store the sprayer on
its side.
5