Maintenance - MrHeater Big Buddy Instrucciones De Operación Y Manual De Usuario

•
Check all hose connections for leaks with soapy water at
the threaded connection under the domed plastic cover
where the hose connector screws into the regulator and
at LP-gas supply cylinder. SEE WARNING! ON
PLASTIC DOORS.
•
Depress and turn Control Knob counterclockwise to
„PILOT‰ position and hold down for 1 - 5 minutes. This
may take longer to purge air from the supply hose
depending on the length of the hose being used.
•
Depress and turn Control Knob counterclockwise to „PI-
LOT‰ position. Ignitor will spark to light the pilot burner.
(If needed, repeat these steps until pilot lights) and
continue to hold control knob down in „Pilot‰ position
for 30-60 seconds.
•
After lighting pilot, release knob. Knob should return
to fully extended position. To operate heater slightly
depress knob and gently turn to lock in desired position.
• Turn control knob to „LO‰ or „MD‰ position to light
heater. Leave on „LO‰ or „MD‰ position until first
burner tile has turned bright orange.
•
After first burner tile has turned bright orange, adjust
heat output by turning Control Knob to desired position
(„LO‰, „MD‰ or „HI‰ setting).
Caution: Do not try to adjust heating levels by using
the propane tank shut-off valve,
:
Warning
DO NOT OPERATE HEATER UNLESS CONTROL KNOB IS LOCKED
IN A POSITION MARKED „HI‰, „MD‰, „LO‰or „PILOT‰. NEVER
SET CONTROL KNOB BETWEEN LOCKED POSITIONS. POOR
COMBUSTION AND HIGHER LEVELS OF CARBON MONOXIDE
MAY RESULT.
•
Installation of 4 D-cell batteries is required for fan
operation. Battery box is located on lower back panel of
heater. Follow instructions on battery cover for correct
battery installation. See figure 2.
•
Heater fan can also be powered by electrical adapter,
F276127. Required adapter to be 6 volt DC up to 800
milliamp current with positive tip polarity. See figure 2.
•
To shut off heater, shut off propane at supply tank,
allow heater to use-up propane in supply line until
heater shuts off, then slightly push down and turn
Control Knob clockwise to „OFF‰ position.
•
CAUTION: After turning heater off, wire guard will
remain hot. Allow to thoroughly cool before storing.
•
When not in use, the gas must be turned off at the LP-
gas supply cylinder. As stated before allow heater to use
up propane in supply line until heater shuts off. When
the LP-gas supply cylinder is not disconnected from
the heater, the heater and the cylinder must be stored
outdoors, in a well ventilated space, out of reach of
children, and must not be stored in a building, garage
or any other enclosed area.
•
Indoor storage of the heater is permissible only if the
cylinder is disconnected and removed from the heater.
Cylinders must be stored outdoors out of the reach of
children and must not be stored in a building, garage or
any other enclosed area.

MAINTENANCE:

Always keep the heater area clear and free from combustible
materials, gasoline and other flammable vapors and liquids.
Keep the vent areas (slots in the bottom and the top at the front
of heater) clear at all times.
Visually inspect the pilot flame and burner periodically during
use. The pilot flame should be blue in color (not yellow) and will
extend beyond the thermocouple. The flame will surround the
thermocouple just below the tip, see Figure 3. A slight yellow
flame may occur where the pilot flame and main burner flame
meet. The burner(s) should be bright orange (with a slight blue
color around the border, a red-orange haze that is visible on the
ceramic tile is acceptable) and without a noticeable flame.
A blue flame that rolls out at the top of the ceramic tile indicates
an accumulation of dust, lint or spider webs inside the casing
assembly and main burner assembly. If the pilot is yellow or the
burner has a noticeable flame, cleaning may be required. Use
the following procedure to inspect the casing assembly and main
burner assembly.
It is necessary to periodically check the burner(s) orifice and
burner venturi tube to make sure they are clear of insects/nests or
spider webs that may accumulate over time. A clogged tube can
lead to a fire.
1 Allow heater to thoroughly cool before performing any
2 Remove disposable 1 lb. cylinder(s) from heater or turn
3 Remove wire guard from front of heater by gently bend-
Figure 3
4 Remove (4) screws securing back cover to heater. Lift up
5 Remove back cover.
6 Remove (3) screws attaching lower baffle to expose
7 Inspect interior of casing assembly for accumulation
8 Inspect and clean main burner orifice located at bottom
Mr. Heater | Big Buddy 5 Operating Instructions and OwnerÊs Manual
maintenance.
OFF gas supply at remote cylinder valve, and disconnect
hose from heater.
ing to remove from holes in front cover.
slightly to release (2) plastic hooks on top of back cover.
burner air openings.
of dust, lint or spider webs. If necessary, clean interior
of casing assembly with a vacuum cleaner or apply air
pressure. Do not damage any components within casing
assembly when you are cleaning.
of burner venturi tube, by using a vacuum or apply air
pressure at orifice opening.