Kask Zenith X Guia De Inicio Rapido

FIG. 1
OK
FIG. 2
FIG. 3
FIG. 5 FIG. 6
FIG. 7
NOMENCLATURE
8 1 9
13
7
14
12
3
5
6
NO NO
SAFETY HELMET FOR INDUSTRIAL USE
FIG. 4a 4b
KASK S.p.A.
24060 Chiuduno, BG
Via Firenze, 5 - Italy
t. +39 035 4427497
info@kask.com
www.kask.com
EXPLANATORY MARKING DIAGRAM
FAC-SIMILA LABELLING
11
SAFETY HELMET FOR INDUSTRIAL USE. For adequate protection this helmet has to t or to be adjusted to
13
the size of the user's head. The helmet is made to absorb the energy of a blow by partial destruction or damage,
SAFETY HELMET FOR INDUSTRIAL USE. For adequate protection this helmet has to t or to be adjusted to
and even though such damage may not be readily apparent, any helmet subjected to severe impact should be
the size of the user's head. The helmet is made to absorb the energy of a blow by partial destruction or damage,
replaced. The attention of the user is also drawn to the damage of modifying or removing any of the original
and even though such damage may not be readily apparent, any helmet subjected to severe impact should be
component parts of the helmet, other than as recommended by the helmet manufacturer. Helmets should
replaced. The attention of the user is also drawn to the damage of modifying or removing any of the original
not be adapted for the purpose of tting attachments in any way not recommended by the helmet
component parts of the helmet, other than as recommended by the helmet manufacturer. Helmets should
manufacturer. Do not apply paint, solvents, adhesives or self-adhesive labels, except in accordance with not be adapted for the purpose of tting attachments in any way not recommended by the helmet
7
instructions from the helmet manufacturer. For cleaning, maintenance or disinfection, use only substances
manufacturer. Do not apply paint, solvents, adhesives or self-adhesive labels, except in accordance with
that have no adverse effect on the helmet and are not known to be likely to have any adverse effect upon
instructions from the helmet manufacturer. For cleaning, maintenance or disinfection, use only substances
that have no adverse effect on the helmet and are not known to be likely to have any adverse effect upon the wearer, when applied in accordance with the manufacturer's instructions and information.
the wearer, when applied in accordance with the manufacturer's instructions and information.
2
DATE OF MANUFACTURE
10
4
USE AND CARE BOOKLET
ZENITH X / ZENITH X AIR
PRODUCT OF ITALY
ANSI/ISEA Z89.1
TYPE 1 CLASS C / E
EXPLANATORY MARKING DIAGRAM
EXPLANATORY MARKING DIAGRAM
1 MANUFACTURER 5 HELMET WEIGHT
1 MANUFACTURER 5 HELMET WEIGHT
2 MODEL NAME 6 SIZE IN CM
2 MODEL NAME 6 SIZE IN CM
3 REFERENCE TO LEGISLATION
3 REFERENCE TO LEGISLATION
4 DATE OF MANUFACTURE 7 IDENTIFICATION NUMBER
4 DATE OF MANUFACTURE 7 IDENTIFICATION NUMBER
ADDITIONAL REQUIREMENTS
ADDITIONAL REQUIREMENTS
FAC-SIMILE LABELLING
FAC-SIMILE LABELLING
1 KASK S.p.A. 5 1,01lb - 460 g
1 KASK S.p.A. 5 1,01lb - 460 g
2 ZENITH X 6 Adjustable
2 ZENITH X 6 Adjustable
3 ANSI Z89.1-2014 6 1/2 - 7 7/8
3 ANSI Z89.1-2014 6 1/2 - 7 7/8
Type I Class E 52 - 63 cm
Type I Class E 52 - 63 cm
4 impressed on the shell 7 20.0000.0001
4 impressed on the shell 7 20.0000.0001
Complies with requirements of the European Standard
EN12492:2012 - Shock energy absorption capacity -
Complies with requirements of the European Standard
Clauses 4.2.1.2 (front), 4.2.1.3 (lateral), 4.2.1.4 (rear);
EN12492:2012 - Shock energy absorption capacity -
Penetration - 4.2.2; Retention system strength - 4.2.3;
Clauses 4.2.1.2 (front), 4.2.1.3 (lateral), 4.2.1.4 (rear);
Retention system effectiveness (Roll off) - 4.2.4.
Penetration - 4.2.2; Retention system strength - 4.2.3;
www.kask.com
Retention system effectiveness (Roll off) - 4.2.4.
www.kask.com
6 - 7
1/2 7/8
Size: ZENITH X
52 - 63 cm
ADJUSTABLE