Westin 25-0500 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
STEP BAR ASSEMBLIES
ENSAMBLES DE ESTRIBOS
MONTAGES DE MARCHE-PIEDS
25-0500 25-0505
26-0505 25-0630
26-0630 26-0635
25-0890
ITEM QTY
1,2 2 STEP BAR, PASSENGER (1) AND DRIVER (2)
3 2 FRONT BRACKET
4 2 REAR BRACKET
5 4 M12-1.75 X 120MM HEX HEAD BOLT
6 4 1/2-13 X 1.75" HEX HEAD BOLT
7 8 1/2" FLAT WASHER
8 8 1/2" LOCK WASHER
1,2 2 ESTRIBOS, ACOMPAÑANTE
3 2 SUPPROT DELANTERAS
4 2 SUPPORT TRASERAS
5 4 PERNOS CON CABEZA HEXAGONAL M12-1,75 X 120MM
6 4 PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 1,75"
7 8 ARANDELAS PLANAS DE 1/2"
8 8 ARANDELAS DE PRESIÓN DE 1/2"
1,2 2 MARCHE-PIEDS,
3 2 SUPPORTS AVANT
4 2 SUPPORTS ARRIERE
5 4 BOULONS A TETE HEXAGONALE M12 1,75 X 120MM
6 4 BOULON A TETE HEXAGONALE DE 1/2-13 X 1,75 PO
7 8 RONDELLE PLATE 1/2 PO
8 8 RONDELLE A FREIM DE 1/2 PO
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions com-
pletely before beginning.
STEP 2.
Attach brackets to vehicle body mounts using metric bolts as shown.
STEP 3.
Attach step bar to brackets using 1/2" fasteners.
for your vehicle. Tube should not touch vehicle body.
STEP 4.
Make sure step bar and brackets are properly aligned with vehicle and tighten fasteners. Recommended torque
value is 79 Ft. Lbs. for 12mm bolts and 64 Ft. Lbs. for 1/2" fasteners.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g.
Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to
corrosion.
PASO 1.
Retire el contenido de la caja y verifique que ninguna pieza se haya dañado. Verifique que no falte ninguna
pieza. Lea las instrucciones completamente antes de comenzar.
PASO 2.
Instale los soportes en las bases de montaje de la carrocería del vehículo con los pernos métricos como se
muestra.
PASO 3.
Coloque el estribo en los soportes con los sujetadores de 1/2".
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1988-98 GMC C/K SERIES PICKUP REGULAR AND EXTENDED CAB
APLICACIÓN:
APPLICATION: CAMIONETTE SERIE C/K GMC, CABINE REGULIERE ET RALLONGEE, 1988-98
EXTENDED CAB
26-0500
CABINA EXTENDIDA
25-0635
CABINE RALLONGEE
25-0885
CONTENTS - CONTENIDO
(1)
PASSAGER (1) ET CONDUCTEUR (2)
1992-99 GMC YUKON 2DR;
1992-94 CHEVY BLAZER 2DR; 1995-99 CHEVY TAHOE 2DR
PICKUP GMC SERIE C/K CON CABINA REGULAR Y EXTENDIDA, MOD. 1988-1998
GMC YUKON 2DR, MOD.1992-1999;
CHEVY BLAZER 2DR, MOD. 1992-1994; CHEVY TAHOE 2DR, MOD. 1995-1999
GMC YUKON 2 PORTES, 1992-99 ;
CHEVY BLAZER 2 PORTES 1992-94 ; CHEVY TAHOE 2 PORTES 1995-99
- CONTENU
Y CONDUCTOR (2)
NOTE:
Use correct hole location for the rear leg of step bar
NOTA:
WO:
REGULAR CAB
3
CABINA REGULAR
CABINE REGULIERE
TOOLS - HERRAMIENTA
3/4" SOCKET
3/4" WRENCH
15MM SOCKET
18MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 3/4"
LLAVE DE TUERCAS DE 3/4"
DADO DE 15MM
DADO DE 18MM
MANERAL
LLAVE DE TORQUE
DOUILLE 3/4 PO
CLE 3/4 PO
DOUILLE 15MM
DOUILLE 18MM
CLIQUET
CLE DE COUPLE
Use el agujero correcto del vehículo
75-0554 REVISION B 2/27/08
4
- OUTILS