Technical Specifications - Master ARCO Manual De Uso

433,42 MHz
Dear Customer, thank you for purchasing a MASTER
S.p.A. product. This guide contains all the information you
will need concerning the use of this product. Read the
instructions carefully and keep them for further
consultation.
ARCO is designed specifically to control sun awnings,
blinds, roller shutters, screens or similar items. All other
use beyond the field defined by MASTER S.p.A. is
forbidden. This, as well as the breach of the instructions
given in this guide, shall release MASTER S.p.A. from any
liability and shall annul the product warranty. Water,
humidity, heat sources, accidental falls can damage the
device. Do not use abrasive products or solvents to clean
the product.
Package contents
- 1 transmitter
ARCO5 - ARCO10 - ARCO20
- 1 CR2032 lithium battery
- 1 wall bracket
- 2 dowels
- 1 this manual
All products and technical specifications given in this document are
subject to variation without notice. Unless previously and
specifically authorised by the manufacturer, the device must be
used exclusively with receivers produced by the same
manufacturer. The manufacturer shall not be liable for damage
resulting from improper, incorrect or unreasonable use.
rev03_22.06.17
www.mastermotion.eu
Sun/automatic lowering function
By the «SUN On / Off " button you can activate / deactivate the SUN function or the AUTOMATIC LOWERING function, in the receivers equipped with these functions. To modify the setting:
A) Select the channel (excluded sequencer channel and groups)
B) Press until the state of the yellow LED varies (about 2seconds)
C) If YELLOW LED IS ON: sun/automatic lowering function active
NOTE: In ARCO2 the «Sun/Automatic lowering» function is active for both channels: if you enable it for channel 1, it is automatically activated for channel 2 and viceversa
that some receiving devices do not associate any operations to some transmitter buttons or that associate to the transmitter buttons some operations different from what it is described. In
this case consider the instruction manual of the receiving device.
2. ENABLING/DISABLING GROUPS AND CHANNELS
With transmitters ARCO 5, ARCO 10 and ARCO 20 you can turn off the channels that are not used; this will facilitate the use of the transmitter because when you scroll through the list of
channels, you find only those actually used. It's possible, with the same procedure, reactivate the channels.
The procedure is as follows:
A) Press STOP and then MENU and hold the buttons for about 3 seconds, until the ch symbol is displayed.
B) Press STOP. 01 will appear.
C) If YELLOW LED IS ON:channel/group enabled / If RED LED IS ON:channel/group enabled
D) Press STOP to modify the setting.
E) If necessary,press PREV and NEXT to select another channel/group and return to point C.
F) To exit, press twice MENU or wait about 15 seconds (the display switches off).
3. DELAY OF TRANSMISSION ON GROUPS AND SEQUENCER CHANNEL
ARCO 2, ARCO 5 and ARCO 10 transmitters have a virtual channel called Sequencer, which sends the selected command in succession for all active radio channels. To select the
Sequencer, scroll the list of channels until SE symbol appears. The ARCO 20 transmitter is equipped with 4 virtual channels (called Groups, indicated with G1, G2, G3, G4) which send the
selected command in succession for all the active radio channels belonging to the group. To select a group, scroll the list of channels until the symbols G1, G2, G3 and G4 appear.
It is possible to set the interval (from 1 to 10 sec) of time which must pass between the transmission on one channel and the next. The factory sets the delay at 1 second. The use of high
intervals of time can negatively effect on the battery life.
To modify the setting:
A) Press STOP and then MENU and hold the buttons for about 3 seconds, until the ch symbol is displayed.
B) Press NEXT. The Sd symbol appears on the display.
C) Press STOP. The currently set value appears on the display (from 01 to 10 sec).
D) Use PREV and NEXT to set the required value.
E) Press STOP to save the setting.
F) To exit, press 1 time MENU or wait about 15 seconds (the display switches off).
4. SETTING THE CHANNELS BELONGING TO A GROUP (only ARCO20)
The ARCO 20 transmitter is equipped with 4 virtual channels (Groups, indicated by G1, G2, G3, G4) which send the selected command in succession for all the active radio channels
belonging to the group. It is possible to associate up to 20 channels to each group.
To set different groups, follow the procedure:
A) Press STOP and then MENU and hold the buttons for about 3 seconds, until the ch symbol is displayed.
B) Press twice NEXT. G1 symbol appears on the display. To select another group press NEXT.
C) Press STOP. Channel 01 appears.
D) If YELLOW LED IS ON: channel belongs to the group / If RED LED IS ON: channel not belongs to the group
E) Press STOP to modify the setting.
F) If necessary, press PREV and NEXT to select another channel and return to point E.
G) To exit, press twice MENU or wait about 15 seconds (the display switches off).

Technical specifications

R
- Power supply:
- Operating temperature:
- Operating frequency:
User manual:
- Operating frequency band:
ARCO
- Max radiated power, e.r.p. :
Notes on radio systems
ARCO 2
Do not use radio systems in places with strong interference (for example, near police stations, airports, banks, hospitals).
ARCO 5
It is in any case advisable to carry out a technical inspection prior to installing any radio system in order to identify possible
sources of interference.Radio systems can be used where any disturbances or malfunction of the transmitter or receiver
ARCO 10 do not constitute a risk factor, or if such factor is eliminated using appropriate safety systems.The presence of radio
devices working at the same transmission frequency (433.42 MHz) may interfere with the radio receiver and reduce the
range of the system, limiting functionality.
ARCO 20
Disposal
At the end of the product life cycle, dispose of the device in compliance with local
regulations. This product could contain substances that are harmful to human health and
the environment: do not dispose of the product in domestic waste.
Fixing the wall bracket
A) Fix the bracket to the wall using the supplied plugs (distance between holes 36 mm).
B) Cover the screw heads with the coverage provided.
C) Hang the transmitter to the support.
Battery insertion/replacement
The transmitter is powered by a battery C R2032. To insert the
battery, remove the battery cover on the back of the
transmitter, insert the battery respecting the polarity, close the
cover. Use of batteries different than those referred can
cause an explosion hazard. Used batteries must be
discarded in appropriate containers. It it recommended to
replace the battery every 2 years.
1. FUNCTIONS ASSOCIATED WITH THE TRANSMITTER BUTTONS
Basic functions
Favorite position
n° 1 CR2032 lithium battery
0° C / +55°C
433.42 Mhz
433,050 – 434,790 Mhz
channel -/+
up
prev/next
stop
right orientation
down
left orientation
To memorize:
Press STOP and then FOR ME and hold
the buttons until the motor signalation (about 5 seconds)
- N° of channel ARCO:
- N° of channels ARCO2:
- N° of channels ARCO5:
- N° of channels ARCO10: 10 + sequencer channel
<10 mW - N° of channels ARCO20: 20 + 4 groups
SUN On/Off
FOR ME
1
2 + sequencer channel
5 + sequencer channel
MENU PROG
access to the
MENU
receiver menu
transmitters
PROG
insertion-deletion
To recall:
It is possible