K Tool International KTI-81798A Manual Del Propietário página 5

KTI-81798A
1" DRIVE IMPACT WRENCH WITH 6" EXTENDED ANVIL
OWNERS MANUAL
REF. NO. PART NO. DESCRIPTION
1 KTP81798A01 Screw (M8x35)
2 KTP81798A02 Lock Washer (8)
3 Oil Seal (Incl. w/ #5)
4 KTP81798A04 Hex Socket Head Set Screw (M8x6)
5 KTP81798A05 Front Casing Assy. (Incl. #3, 5, 9)
6 KTP81798A06 Lock Washer (6)
7 KTP81798A07 Hex Socket Cap Screw (M6x20)
8 KTP81798A08 Side Handle
9 Anvil Bushing (Incl. w/ #5)
10 KTP81798A10 Front Washer
11 KTP81798A11 O-Ring
12 KTP81798A12 Retainer Ring (included w/#13)
13 KTP81798A13 Extended 6" Anvil (Incl. #12-14)
14 KTP81798A14 O-Ring (included w/#13)
15 KTP81798A15 Hammer Cage
16 KTP81798A16 Hammer
17 KTP81798A17 Hammer Cam
18 KTP81798A18 Spacer
19 KTP81798A19 Front Cylinder Gasket
20 KTP81798A20 Motor Housing Assy. (Incl. #20, 22, 23, 26, 27)
21 KTP81798A21 All-Metal Locking Nut (M8)
22 Bearing (Incl. w/ #20)
23 Front Plate (Incl. w/ #20)
24 KTP81798A24 Rotor
25 KTP81798A25 Rotor Blade (pack of 5)
26 Spring-type Straight Pin (Incl. w/ #20)
27 Cylinder (Incl. w/ #20)
KTI-81798A
QTY. REF. NO. PART NO.
4 28 KTP81798A28
8 29 KTP81798A29
1 30 KTP81798A30
1 31 KTP81798A31
1 32 KTP81798A32
4 33 KTP81798A33
4 34 KTP81798A34
1 35 KTP81798A35
1 36 KTP81798A36
1 37
1 38 KTP81798A38
1 39
1 40
1 41
1 42 KTP81798A42
1 43 KTP81798A43
1 44 KTP81798A44
1 45
1 46
1 47 KTP81798A47
4 48 KTP81798A48
1 49 KTP81798A49
1 50 KTP81798A50
1 51 KTP81798A51
1 52 KTP81798A52
2 53 KTP81798A53
1 Also available:
KTP81798ATK Tune-Up Kit (Incl. #3, 11, 12, 14, 19, 25 (5), 31, 43, 46, 50)
Not Shown – KTP81798APLK – Product Label Kit
5
DESCRIPTION
Spring-type Straight Pin
Rear Plate
Bearing
Rear Cylinder Gasket
Rear Casing Assy. (Incl. #32, 37, 45, 46)
Hex Socket Cap Screw
Spring-type Straight Pin (4 x 22)
Spring-type Straight Pin (4 x 24)
Trigger
Reverse Valve Bushing (Incl. w/ #32)
Reverse Valve Assembly (Incl. #38-41)
Steel Ball (Incl. w/ #38)
Spring (Incl. w/ #38)
Spring-type Straight Pin (Incl. w/ #38)
Spring-type Straight Pin (4 x 28)
O-Ring
Screw
Throttle Valve Bushing (Incl. w/ #32)
Rubber Seal (Incl. w/ #32)
Throttle Valve Plunger
Steel Ball (12.7mm)
Spring
O-Ring
Air Inlet Connector
Rubber Shield
Flat Washer (8)
QTY.
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
8
04/12/16