NightStick XPP-5418GX-K01 Manual De Instrucciones

Instruction Manual
XPP-5418GX/RX-K01
Please read these instructions before using your Nightstick XPP-5418 Intrinsically
Safe Flashlight. They include important safety information and operating instructions.
THE XPP-5418GX/RX IS APPROVED FOR USE
Bayco Products, Inc.
640 S. Sanden Blvd., Wylie, TX 75098
Ex ia FLASHLIGHT FOR USE IN HAZARDOUS LOCATIONS
CLASS I DIV 1 GRPS A-D T3
CLASS II & III DIV 1 GRPS E-G T135ºC
ID 4003544
CLASS I ZONE 0 AEx ia IIC T3 Ga
INTRINSICALLY SAFE
Ex ia IIC T3 Ga
SECURITE INTRINSEQUE
II 1 G Ex ia op is IIC T3 Ga
2575
WARNINGS:
Replace batteries in a non-hazardous location.
Use only Energizer AA Model E91 or EN91 batteries.
AVERTISSEMENT:
Remplacer les piles dans une zone non dangereuse.
Utiliser uniquement les piles Energizer AA - modèle E91 ou EN91.
WARNINGS - INTRINSICALLY SAFE
y Warning: Use only the approved non-rechargeable batteries listed below.
y Warning: Do NOT attempt to use rechargeable AA batteries with this light.
y Warning: To prevent ignition of a hazardous atmosphere, do not open the lens bezel
in the hazardous environment. This task must ONLY be performed in an area known
to be non-hazardous.
y Warning: When exchanging batteries, use only Energizer EN91 or Energizer
E91 batteries.
y Warning: To prevent ignition of a hazardous atmosphere, the AA batteries must only
be exchanged in an area known to be non-hazardous.
y Warning: To reduce the risk of explosion, do not mix new batteries with used
batteries, or mix batteries from different manufacturers.
y Warning: Substitution of components may impair intrinsic safety.
SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY
For personal safety, always confirm the rating of any known hazardous or potentially
hazardous location where the light is to be used.
BATTERY INSTALLATION
WARNING: In order to maintain the XPP-5418's Intrinsically Safe rating, the only
AA batteries certified for use with this light are the Energizer EN91 or Energizer
E91 batteries.
y Do not attempt to use any other brand or model of AA batteries.
y Do not attempt to use any type of rechargeable AA batteries.
Warning: To prevent ignition of a hazardous atmosphere, do not remove the lens
bezel or the reflector / battery carrier in the hazardous environment. This task
must ONLY be done in an area known to be non-hazardous.
y Loosen the locking screw located on the side of the lens cap. NOTE: Do NOT
attempt to completely remove the locking screw. Doing so is not necessary and may
damage the threads. The screw simply needs to be loosened enough to allow the lens
bezel to unscrew.
y Unscrew the lens bezel from the housing in a counter-clockwise direction.
y Turn the light upside down and carefully shake the light in order to remove the
batteries. Allow the batteries to slide into your hand.
y Using 3 – AA Energizer EN91 or Energizer E91 batteries (make sure that all 3
batteries are of the same model), install the batteries in the carrier paying close
attention to the markings inside the housing for proper battery terminal polarity
alignment.
y Replace the lens bezel by screwing it onto the housing in a clockwise direction.
y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage the
threads and impact the light's Intrinsic Safety.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
THE XPP-5418-K01 COMES WITH THE NS-HMC6 MULTI-ANGLE MOUNT THAT CAN
XPP-5418GX/RX
BE ATTACHED TO ANY FIRE HELMET OR HARD HAT.
type of mount is needed.
Ex ia op is IIC T3 Ga
Intertek ITS 13 ATEX27837X
IECEx ITS 16.0067X
-20ºC ≤ Tamb ≤ +40ºC
1.5V/Cell with three in series
Energizer E91 or EN91
Segurança
INMETRO
Ex ia op is IIC T3 Ga
(-20ºC ≤ Tamb ≤ +40ºC)
NCC 15.0286 X
ASSEMBLY
position the light appropriately for the optimum clearance and illumination.
THE XPP-5418 HAS TWO SEPARATE LIGHTING MODES:
MOMENTARY FLASHLIGHT MODE
the light off.
CONSTANT-ON FLASHLIGHT MODE
and release the body switch again to turn the light off.
LIMITED LIFETIME WARRANTY
and materials for the original purchaser's lifetime. The Limited Lifetime Warranty
includes the LEDs, housing and lenses. Rechargeable batteries, chargers, switches,
electronics and included accessories are warranted for a period of two years with proof
of purchase. Normal wear and failures which are caused by accidents, misuse, abuse,
faulty installation and lightning damage are excluded.
is the only warranty, expressed or implied, including any warranty of merchantability or
fitness for a particular purpose.
support/warranties. Retain your receipt for proof of purchase.
INS-XPP-5418GX/RX-K01-DL-20
XPP-5418 with Brim Mount
ATTACHING HELMET MOUNT
Two mounting components are included that can be changed depending on what
y Brim Mount - Mounts on brim of helmet or hard hat..
y Slot Mount - Slides into helmet accessory slot.
NS-HMC6 Helmet Mount Kit
y Fit the Light Mount (A) into the slot of either the Brim Mount or Slot Mount (B) and
securely tighten using the thumb screw (C).
y Securely attach the brim or slot mount to the helmet.
y Place the flashlight inside the Light Mount
SET THE ANGLE OF THE MULTI-ANGLE MOUNT
Once mounted to the helmet, the user can change the angle of the mount in order to
OPERATION
Lightly press the body switch for momentary operation. Release the switch to turn
Press the body switch until it clicks and then release for constant-on mode. Press
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
We will repair or replace this product should we determine it to be defective. This
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-product-
XPP-5418 with Slot Mount
12-14-2020