NightStick Fortem XPP-5466 Manual De Instruccion

Instruction Manual
Fortem™ XPP-5466
US PATENT 9,713,217
Please read these instructions before using your Nightstick XPP-5466. They include
important assembly and operating instructions.
THE XPP-5466 IS APPROVED FOR USE
Bayco Products, Inc.
E 467756
ID 4001184
INTRINSICALLY SAFE
SECURITE INTRINSEQUE
0359
Do not change batteries in hazardous location.
Use only Energizer 123 Batteries
Conforms to:
ANSI/UL STD 913, ANSI/UL 60079-0
WARNINGS - INTRINSICALLY SAFE
y Warning: Use only the approved non-rechargeable batteries listed below.
y Warning: Do NOT attempt to use rechargeable CR-123 batteries with this light.
y Warning: To prevent ignition of a hazardous atmosphere, do not open the battery
compartment in the hazardous environment. This task must ONLY be performed in an
area known to be non-hazardous.
y Warning: When exchanging batteries, use only ENERGIZER CR-123 BATTERIES.
y Warning: To prevent ignition of a hazardous atmosphere, the CR-123 batteries must
only be exchanged in an area known to be non-hazardous.
y Warning: To reduce the risk of explosion, do not mix new non-rechargeable batteries
with used non-rechargeable batteries, or mix non-rechargeable batteries from different
manufacturers.
y Warning: Substitution of components may impair intrinsic safety.
SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY
y For personal safety, always confirm the rating of any known hazardous or potentially
hazardous location where the light is to be used.
PACKAGE CONTENTS
y 1 – XPP-5466 Helmet Mounted Multi-Function Dual-Light Flashlight
y 2 – CR-123 Lithium Batteries
y 2 – 5/16" - 18 x 1/4" Brim Mounting Allen Set Screws (installed in mount) – for Fire
Helmets
y 2 – 5/16" - 18 x 3/8" Brim Mounting Allen Set Screws (loose) – for Hard Hats
y 1 – 5/32" Allen Wrench
y 1 – Mounting shim
APPLICATION
The XPP-5466 Helmet Mounted Multi-Function Dual-Light™ Flashlight is a single
self-contained flashlight, a floodlight and a Dual-Light mode flashlight designed for
attaching to virtually any Fire Helmet or Hard Hat.
Both the flashlight and the floodlight have user-selectable brightness levels and
each be operated independently or at the same time. In high-brightness mode, the
flashlight produces 220 Lumens and is distance rated at 183 meters. The light is IP-X7
waterproof and is drop rated at 2 meters.
The Helmet Mounted Multi-Function Dual-Light Flashlight can be attached to either
side of virtually any Fire Helmet or Hard Hat and provides a wide range of adjustability
options. This adjustability allows the user to best position the light for purposes of
providing clearance around face shields, goggles or other potential obstructions while
still allowing the floodlight to point in a downward direction regardless of the angle of the
brim of the helmet.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • USA • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
XPP-5466
CLASS I DIV 1 GRPS A-D T4
CLASS II & III DIV 1 GRPS E-G T135°C
CLASS I ZONE 0 AEx ia IIC T4 Ga
CLASS I ZONE 0 Ex ia IIC T4
-20ºC ≤ Tamb ≤ +40ºC
3.0V/Cell / Energizer 123
WARNINGS:
Certified to:
CAN/CSA STD C22.2 No 157
CAN/CSA STD C22.2 No 60079-0
CAN/CSA STD C22.2 No 60079-11
CSA STD C22.2 No 25
INSTALLING BATTERIES INTO THE 5466
WARNING: In order to maintain the XPP-5466's Intrinsically Safe rating, the
only CR-123 batteries certified for use with this light are the ENERGIZER 123
BATTERIES.
y Do not attempt to use any other brand or model of CR-123 batteries with this light.
y Do not attempt to use any type of rechargeable CR-123 batteries with this light.
Warning: To prevent ignition of a hazardous atmosphere, do not open the battery
compartment door in the hazardous environment. This task must ONLY be done
in an area known to be non-hazardous.
y To install the CR-123 Lithium Batteries in the 5466, begin by unscrewing the screw
on the battery compartment door. (Image 1)
y Using 2 – ENERGIZER 123 BATTERIES (make sure that both batteries are of the
same model), install the batteries in the back of the light paying close attention to the
markings inside the battery compartment for proper battery terminal polarity alignment.
(Image 2)
y Close the battery compartment door.
y Tighten locking screw. CAUTION: Do NOT over-tighten. Doing so may damage the
threads and impact the light's Intrinsic Safety. (Image 3)
Image 1
ADJUSTING THE ORIENTATION AND/OR ANGLE OF THE MOUNT
The mount on the top of the light is designed to be adjustable in terms of which side
of the helmet it can be mounted to. Additionally, adjustments to the angle of the light can
be made to refine the angle of the beam in relation to the helmet. Out of the packaging,
the mount is set up for attachment to the right side of the helmet. If the light needs to be
mounted to the other side of the helmet or if the angle of the light needs to be adjusted,
use the following steps to make those adjustments:
Using the included 5/32" Allen Wrench, loosen and then remove the Angle Lock
Socket Head Cap Screw and separate the Mount from the rest of the assembly. (Image 4)
If the angle of the light needs to be adjusted, loosen the Angle Adjustment Socket
Head Cap Screw found below the Mount using the 5/32" Allen Wrench, adjust the angle
as needed and then tighten the Angle Adjustment Socket Head Cap Screw completely.
(Image 5)
Reinsert the Mount into the rest of the assembly and reinstall the Angle Lock Socket
Head Cap Screw paying close attention to the fact that the Mount is positioned correctly
based on the side of the helmet that the light is to be mounted to. (Image 6)
NOTE: THIS PRODUCT IS NOT DESIGNED TO SWIVEL ONCE THE ANGLE OF
THE LIGHT HAS BEEN SET.
Image 4
INS-XPP-5466-16
Image 2 Image 3
Image 5 Image 6
03-28-2018