Master SET METIS IRO Manual Del Usuario página 7

IRO
U P P
E R L
I M I T
S W I
T C H
+
+
L O W
E R
L I M
I T S
W I T
C H
If the fabric is wrapped from behind the roller: the blue screw adjusts the lower
limit switch, the white screw adjusts the upper limit switch
07. MEMORIZATION/DELETION OF RADIO DEVICES
A
Bring the motor to the intermediate position.
D
TRANSMITTER
(1) (1)
STOP
Notes:
ü
(1) Radio devices: hold the button on the transmitter or the radio sensor to be stored until the motor performs the signal in point E. In particular, to
memorize or delete a sensor powered by battery, you may need to hold the button up to 10 seconds. If the button is not pressed
within 15 seconds, the motor exits the programming and signals it with 2 downward movements.
ü
If only one transmitter is stored, the motor does not permit its deletion (the motor exits the programming and signals it with 2 downward movements).
08. "TEST RADIO" FUNCTION
As soon as the motor stores a wind or sun/wind sensor, a communication control is automatically activated between the wind sensor and the device. If the
communication is lost for more than 60 minutes, the motor performs an upward movement to protect the blind. This automatic manoeuvre is performed every 60
minutes until the reactivation of the radio communication. The factory recommends to keep the "test radio" active in order to identify in good time any malfunction of
the radio sensor or of the radio communication. To modify this function:
ARCO
01. Bring the motor in an intermediate
position.
02. Press MENU for about 5 sec, until
«rS» appears on display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press PREV
To activate: press NEXT
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
MOTOR TO THE RIGHT
BLUE screw
-
WHITE screw
B
Press PROG on a transmitter already
stored in memory for around 5 seconds.
WITHIN 15 SECONDS PRESS:
SENSOR
(1)
P1
P1
FLUTE, KUADRO, KORT
01. Bring the motor in an intermediate
position.
02. Holding down STOP, press PROG
for about 1 sec, until LEDs light
03. Press 1 time UP / 7 times DOWN.
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
MOTOR TO THE LEFT
WHITE screw
BLUE screw
If the fabric is wrapped from behind the roller: the blue screw adjusts the lower
limit switch, the white screw adjusts the upper limit switch
RAIN SENSOR
(1)
P2 P2
VISIO
01. Bring the motor in an intermediate
position.
02. Press MENU, «Menu rx» appears
on display
03. Press 1 time PREV / 7 times NEXT.
«17» appears on display
04. Press STOP. The motor signals:
1 up = active, 1 down = inactive
05. To deactivate: press DOWN
To activate: press UP
06. Press STOP. The motor signals:
1 up = active, 1 down = inactive
T C H
S W I
I M I T
E R L
+
U P P
-
+
C H
S W I T
I M I T
E R L
L O W
C
x2
The motor performs 2 upward movements.
E
x1
Stored !
x1
Deleted !
The motor signals the operation performed.
Advanced Info
Other transmitters...
See the User manual
of the transmitter at
«RECEIVER MENU -
Function 17 -
section:
Test radio»