Fcc Notice; Industry Canada Statement - CREE LIGHTING CSC-CWD Manual De Instrucciones

Wall Control Troubleshooting
Issue
Wall Control LED does not blink
in a 2-blink sequence prior to
™
OneButton Setup
Wall Control will not join a
network
Replaced existing Wall Control
and fixtures will not turn on
Wall Control will not control
fixtures

FCC NOTICE

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate the device.
This device has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the device is operated in a commercial
environment. This device generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this device in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
In addition, this device complies with ICES-003 of the Industry
Canada (IC) Regulations.
© 2020 Cree Lighting, A company of IDEAL INDUSTRIES. All rights reserved. For informational purposes only. Content
is subject to change. See www.creelighting.com/warranty for warranty and specifications. Cree
registered trademarks and the Cree SmartCast Technology logo is a trademark of Cree, Inc. SmartCast
trademark of Cree Lighting, A company of IDEAL INDUSTRIES.
3 of 3
Resolution
Check wiring
(LINE/NEUT/GND required)
Check connected load for wireless dimmers
without neutral. Minimum load must be wired
to dimmer (minimum load indicated on spec
sheet).
Reset Device and verify 2-blink sequence for
the LED
Check wiring (NEUT required)
NOTE: LED may illuminate if NEUT not
connected
Check connected load for wireless dimmers
without neutral. Minimum load must be wired
to dimmer (minimum load indicated on spec
sheet).
Reset Device and verify 2-blink sequence for
the LED
Check Wiring (each fixture shall be wired with
constant HOT)
Check group assignments with Configuration
Tool
RESET WALL CONTROLS
STEP 1:
Press/Hold (approx 30 sec) ON paddle until the LED
flashes fast.
STEP 2:
Briefly release the paddle for less than
1 sec (Fast flashing continues)
STEP 3:
Press/Hold ON paddle for 1 sec until fast flashing stops.
If the blue LED does not respond with the two-blink
sequence, please repeat the RESET procedure.
CLEANING
Clean using a cloth dampened only with water and a little
mild detergent. Use of solvents or hydrocarbon-based
cleaners may cause permanent damage.

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device. In addition, this device complies with ICES-003
of the Industry Canada (IC) Regulations.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
and the Cree logo are
®
, is a registered
®
www.creelighting.com
LPN00838X0001A0_A