Important Safety Instructions; Technical Specifications - Televes T.0X Serie Guía Rápida

O. F. Transmitter
O. F. Transmitter

Important Safety Instructions

EN
Caution Statements
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near
water.
6. Clean only with a dry cloth.
7. Do not block any ventilation
openings. Install in accordance
with the manufacturer's
instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus
(including amplifiers) that produce
heat.
9. Only use attachments/accessories
specified by the manufacturer.
10. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus has
been damaged in any way, such
as power-supply cord or plug is
damaged, liquid has been spilled
or objects have fallen into the
apparatus, the apparatus has been
exposed to rain or moisture, does
not operate normally, or has been
dropped.
Warning
Reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
Apparatus shall not be exposed to
dripping or splashing and no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
Safe operation
Should any liquid or object fall

Technical specifications

Optical transmitter
RF frequency range
RF input level
RF manual gain adjust
CAG control
Flatness
RF parameters
Return losses
Impedance
CSO (CENELEC 42) note 1
CTB (CENELEC 42) note 1
C/N note 1
Laser
Wavelength
Optical
Optical power
Optical return losses
RF connectors
Optical conector
Supply voltage
General Power consumption
Operation temperature
Weight
Dimensions
(1) 42 CENELEC channels plan.1km of standar fiber followed by a 8 outputs splitter. Input power into reference receiver
into the equipment, please refer to
qualified personnel for service.
Safe operation
Ambient temperature should not be
higher than 45°C.
Do not place the equipment near
heat sources or in a highly humid
environment.
Do not place the equipment in a
place where it can suffer vibrations
or shocks.
Please allow air circulation around
the equipment.
Do not place naked flames, such
as lighted candles on or near the
product.
Handling optical connections:
An SC/APC single mode fiber
cable must be used. Remove the
protective cover from the optical
connector on the unit and the cap
on the cable connector.
Carefully align the guides on both
connectors when plugging
cable to the device, then push the
connector all the way in.
Take special care to avoid damaging
the unprotected ends of
connectors, as small scratches,
impurities and/or particles of dirt, oil,
grease, sweat, etc. may significantly
affect the quality of the signal.
To clean the ends of the connectors,
gently rub with a lint-free lens
cleaning cloth, dampened using
additive-free isopropyl alcohol.
Make sure the alcohol evaporates
fully before connecting. Keep the
connector covers and cable caps in
a safe place in case they are needed
MHz
dBmV
dB
dB
dB
dB
Ohm
dB
dB
dB
type
nm
dBm
dB
type
Vdc
mA
ºC / ºF
grs/libs
mm / inch
in the future. Always fit the covers on
the connectors of devices that are
not connected to cables to prevent
the laser beam from damaging the
eyes.
Do not turn the transmitter on
without a fiber optic cable connected
to it.
Safety precautions
Warning.-
This product emits an invisible laser
beam. Avoid contact with laser
radiation. The use of equipment such
as binoculars or magnifying glasses
may increase damage caused to the
eyes.
INVISIBLE LASER RADIATION
DO NOT WATCH DIRECTLY WITH
OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
According to EN 60825-1: 2014
Ref: 234801
Maximum Output: 10dBm
Emitted Wavelength (s): 1310nm
a
Ref: 234811
Maximum Output: 10dBm
Emitted Wavelength (s): 1550nm
the
Caution
- The use of controls or adjustments, as
well as different procedures beyond
those specified in this manual
could result in exposure to harmful
radiation.
- Read and follow the instructions in
this manual very carefully, keep this
manual for future reference.
- Do not use the equipment in a way
that does not conform to these
operating instructions or under any
234801
>52
1310+/-10
50 x 217 x 175 / 1.96 x 8.54 x 6.88
(M2Optics-FOS -FOS 1000A- equipment) is -1dBm.
condition that exceeds the indicated
environmental specifications.
- The user cannot
equipment. For technical assistance,
contact our technical assistance
department.
- The laser beam should not be pointed
at people and/or animals.
Simbology
Equipment designed for indoor
use.
The equipment meets the CE
marking requirements.
The product is EAC certified.
234811
47-1100
15-30
0 ... 14 (steps 2 dB)
15
±1
15 (typ)
75
60
60
>50
MQW-DFB cooled
1550.12 (ITU 100G)
10
50
Female F
SC/APC
12-24
360-220
-5.......45 / 32.......113
850 / 1.87
4 4
service this