Publicidad
Idiomas disponibles
Idiomas disponibles
•
Before taking into operation, every stand has to be checked upon possible damages. If one part of a stand is defective, the stand must not
be taken into operation.
Before lifting or lowering the telescopic tubes, you must always block a safety area around the stand. This safety area must have a
•
diameter of 1.5 times the maximum height.
•
Stands with their loads have to be secured against unintended movements, also in case of fire.
•
Depending upon the individual installation spot, all necessary measures against movement and for securing the standing safety have to
be created.
•
When people are located below the load, all necessary safety measures have to be taken in order to avoid injury. The personnel has to be
instructed on the content of the user manual and on the dangers related with operating stands.
•
Operate the stand only after having become familiar with its functions. Do not permit operation by persons not qualified for operating the
device. Most damages are the result of unprofessional operation!
•
Lifted telescopic tubes always have to be secured with a secondary securing!
•
All fixtures and T-bar attached on a stand must be secured with a secondary attachment!
•
When choosing the installation-spot, please make sure that the stand has to be installed in a way that no person can enter the area below
the stand or its load!
•
This stand must only be installed at a solid, plane, anti-slip, vibration-free and fire-resistant location.
•
Never install any objects offering a large surface for winds (e.g. banners, signs, etc.).
•
The loads have to be installed in a balanced way.
•
Always fix the fixtures with an appropriate safety-rope.
•
The stand must never be moved before having lowered all telescopic tubes!
Never dismount the winch handle or any element of the winch under any circumstances.
•
•
Please consider that unauthorized modifications on the stand are forbidden due to safety reasons!
•
Dry the product after use in damp conditions to avoid triggering corrosion especially when using it near marine environments.
•
The product is not designed to be used immersed in liquids.
•
Never remove the serial code and production date from the stand as this would make the guarantee void.
•
If this stand will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee
becomes void. Furthermore, any other operation may lead to dangers like crash.
Before installing the stand, make sure that the installation area can hold a minimum point load of 5 times the system's load (e.g. weight
•
20 kg - point load 100 kg).
•
The installer is responsible for adhering to the carrying capacity given by the manufacturer, the safety requirements and the qualification
of possible co-workers.
•
The stand must not be left unattended or accessible to unauthorized persons. Keep away children!
•
Stand may not exceed the maximum load of 80kg.
•
The stand should only be set up on a horizontal level surface.
•
The stand must be set up on firm ground capable of taking both the weight of the stand and its load without sinking in.
Carefully check that there are no electrical cables or live parts located in the area occupied by the stand and its load.
•
All loads should be balanced especially when using T-Bar.
•
Periodically check that the steel cables, that raise and lower the telescopic parts, are in good condition. In the even that a cable is frayed
•
or slack, stop using the stand and contact your dealer for repair.
Determine a suitable location and place the tripod.
•
•
Loosen the locking screw and pull the locking pin.
Push the three legs down and put the tripod in the desired position.
•
stability.
•
Check that the stand is vertical and correct if necessary. To do this, loosen the locking screw and the locking pin so that one leg can be
extended to adjust the vertical position of the stand. Check the vertical orientation of the stand using a spirit level.
•
Then unscrew the locking screw from the inner telescopic part and pull out the locking pin.
Turn the winch until the desired height is reached and release the locking pin.
•
Turn the winch again, up or down, so that the locking pin engages and is engaged. Check this with the help of the winch, now it is no
•
longer possible to raise or lower the telescopic part!
•
Tighten locking screw as secondary locking.
•
Repeat upper steps to adjust the height of the second telescopic tube.
•
Finally, rotate the crank approximately a quarter turn to slacken the steel cable.
Telescopic section may not reach maximum height. As soon as "STOP" or "MAX" label is visible on the telescopic tube, lower
the telescopic part immediately.
The legs must be fully extended to ensure maximum
Publicidad
