Publicidad
Idiomas disponibles
Idiomas disponibles
TIMER OPERATION: count down
1. Press C button until the stopwatch
goes to the TIMER mode. The display
is as shown in Fig.18. The top row is
the display for the 1st timer and the
middle row is the display for the 2nd
timer.
2. Press and hold B button for 2
seconds to go into the SET TIMER
mode with the hour digit of the 1
timer blinking.
3. Press A button to set to desired
hour for countdown.
4. Press B to go to the first digit in
minutes and press A to set minutes.
5. Similarly by using B and A buttons
the desired countdown times for the
1st and 2nd timers can be set.
6. Pressing C button once any time
during this TIMER setting sequence
will complete the setting and the timer
is ready to start upon pressing the A
button.
7. Press A to start countdown with the
"1 " at the top right corner blinking and
the timer setting counting down. When
the 1st timer approaches zero, the
timer gives 4 beeps and the 2nd timer
starts counting down immediately.
When the 2nd timer approaches zero,
it gives 2 beeps and the 4 digit
counter at the lowest row advances by
1 automatically.
8. At any time during countdown
pressing A will stop counting.
If only the 1st timer is set the timer is
used as an ordinary countdown timer
and will give 5 times 4 beeps when
the set time is up. The 4 digit counter
also advances by 1 automatically
when
the
timer
reaches
STROKE / FREQUENCE BASE 3 ;
8. Press the button C to go into
« chronograph mode ».
9. Press B during few seconds to go into
« speed mode » (cf fig.14).
10.
Scroll with the button B.
11. Select the numbers with the button
A. The distance has to be set up on
« 180 » (0180.000) and the time unit on
« seconds »
Then, press C to confirm.
12. Start the « chronograph mode »
with the button A. After the third stroke
only, press A again. The line in the
middle indicates the number of strokes
per minute.
All manuals and user guides at all-guides.com
DATA STORED RECALL:
1. Press D to recall data stored. The
display which we call the RACE
RECORD is as shown in Fig. 8.
2. The display shows the date in
which the race was recorded and
MCH-001 (MSP for SPEED mode)
stands for the first race
3. Recorded in LAP/SPLIT mode at
that date.
4. Press D again to recall the 1st LAP
data, as shown in Fig.9.
5. Press D to recall the 2nd LAP data.
6. Press D again shows the stopped
time
7. Press D again to show the average
LAP time
8. Press D again to show the Best
LAP time.
9. The AVERAGE calculation and
BEST record do not take into account
the last section of time before STOP.
st
Therefore, in order for the stopwatch
to keep track of the average and best
records of all laps, always use the B
button until the end of the race.
10.
Pressing D again will go
to the next race records or return to
the 1st race records (if there is no
further race).
MEMORY USED UP:
You have the possibility to clear the
races one by one, or to clear all. From
the chronograph mode (time display
must be put to zero), press the D
button to accede to data stored.
1.
Clear the races one by one:
Choose the race you want to clear and
press B button (race number in the right
down corner). Press and hold A button
when the stopwatch is displaying the
RACE
RECORDS
memories in that race record (when the
zero.
contents in this race record are cleared
the display will show "CLEARED" and
sounds a long beep, if A is released
before
ED
appears.
operation to clear races one by one.
2. Clear all races:
Press A button during some seconds.
« CLEAR »,
« CLEARED »,
CLEAR »,
« ALL
appear successively. "ALL CLEARED"
(SEC).
appears when all data are cleared. The
display comes back to the chronograph
mode (fig.2)
When all the memories have been used
the 4 digit LAP counter at the top left
corner will start blinking to indicate all
memories have been used up. All further
LAP memories will not be recorded in
the memory unless some memories are
cleared as previously indicated. When
there is no memory left pressing A to
start a race will sound 3 short beeps.
Do not leave the stopwatch running if not
in use as that drains a higher power from
the battery.
UPLOAD MODE:
1. In Fig. 20 press D button once will
switch to UPLOAD MODE.
2. Pressing A button will UPLOAD
ALL recorded memories to computer
(if computer is connected). When the
stopwatch is in the process of
uploading, an indicator moves from
right to left. When upload is complete
UPLOAD END is displayed.
3. Press D button to return to PRINT
MODE.
4. Pressing B at the UPLOAD ALL
mode will go to the UPLOAD RACE
mode with display.
5. Pressing A in this mode will only
upload the memories in this race.
6. Press B to select particular race to
upload.
7. Pressing C any time during this
uploading process will stop printing
immediately.
8. If the chronograph is not reset (i.e.
still running or stopped), it will not be
possible to upload and the display will
show UPLOAD 0, there will not be any
action upon pressing A or B.
PRINT MODE:
1. Press C button to go to the PRINT
ALL mode as shown in Fig.20.
2. Pressing A button will print all
recorded memories to the printer (if
printer is connected). When the
stopwatch is in the process of printing,
an indicator moves from right to left.
When printing is complete PRINT
END is displayed.
will
clear
the
3. Pressing B at the PRINT ALL mode
will go to the PRINT RACE mode with
display as shown in Fig.21.
4. Pressing A in this mode will only
print the memories in this race.
5. Press B to select particular race to
Repeat
the
print.
6. Pressing C any time during this
printing process will stop printing
immediately.
7. If the chronograph is not reset (i.e.
« ALL
still running or stopped), it will not be
CLEARED »
will
possible to upload and the display will
show PRINT 0, there will not be any
action upon pressing A or B.
Publicidad
