enbrighten ZW4008DV Manual Del Usario

FCC/IC
En
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Important note: To comply with the FCC RF exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the antenna or the device could result in the
device exceeding the RF exposure requirements and void user's authority to operate the device.
Fr
Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils exempts
de licence d'Industrie Canada. Son utilisation est sujette aux deux conditions suivantes : (1) cet
appareil ne doit pas occasionner de brouillage préjudiciable et (2) cet appareil doit accepter toutes
les interférences reçues, notamment les interférences qui peuvent provoquer un fonctionnement non
désiré.
NOTE DE LA FCC : Le fabricant n'est pas responsable des interférences sur les fréquences
radioélectriques ou télévisuelles pouvant être causées par des modifications non autorisées de ce
matériel. De telles modifications peuvent annuler le droit de l'utilisateur à utiliser cet appareil.
REMARQUE : Cet appareil a été testé et certifié conforme aux limites relatives aux appareils
numériques de catégorie B définies dans le paragraphe 15 des normes FCC. Ces limites ont été
définies afin de fournir une protection raisonnable contre le brouillage préjudiciable en milieu
résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et, s'il n'est pas
installé et utilisé conformément aux instructions, il peut provoquer un brouillage préjudiciable aux
communications radio. Il n'existe toutefois aucune garantie que des interférences ne se produiront
pas au sein d'une installation donnée. Si cet appareil occasionne un brouillage préjudiciable à la
réception radiophonique ou télévisuelle, il suffit d'allumer et d'éteindre l'appareil pour déterminer sa
responsabilité. Nous encourageons l'utilisateur à essayer de corriger ces interférences en appliquant
une ou plusieurs des mesures suivantes :
— Réorienter ou déplacer l'antenne de réception.
— Augmenter la distance entre l'appareil et le récepteur.
— Brancher l'appareil à une prise secteur différente de celle du récepteur.
— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.
Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant
l'exposition aux RF, aucune modification apportée à l'antenne ou au dispositif n'est autorisée. Toute
modification apportée à l'antenne ou au dispositif pourrait faire en sorte que le dispositif dépasse les
exigences d'exposition aux RF et pourrait annuler le droit de l'utilisateur à utiliser ce dispositif.
Es
Este dispositivo cumple con las Especificaciones del apartado 15 de las normas de la FCC y con las
especificaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá aplicables
a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos condiciones: (1)
este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo debe aceptar
toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no deseado.
NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio
o TV ocasionada por modificaciones no autorizadas efectuadas a este equipo. Dichas
modificaciones podrían anular la autoridad del usuario para utilizar el equipo.
NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,
de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para
proveer protección razonable contra interferencias perjudiciales en una instalación residencial. Este
equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa según las
instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No obstante, no
hay garantías de que no ocurrirá interferencia en una instalación en particular. Si este equipo provoca
interferencia perjudicial a la recepción de radio o televisión, lo que puede determinarse encendiendo
y apagando el equipo, se recomienda que el usuario intente corregir la
interferencia por medio de la implementación de una o más de las siguientes medidas:
— Reorientar o reubicar la antena receptora.
— Incrementar la separación entre el equipo y el receptor.
— Conectar el equipo a un tomacorriente de un circuito diferente
del circuito al que está conectado el receptor.
— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para
solicitar asistencia.
Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de
radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier
cambio a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de
exposición de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.
Responsible Party - US Contact Information | Parte responsable - Información de contacto de los
Estados Unidos | Partie responsable - Coordonnées des États-Unis
ZW4008DV:
FCC ID — U2ZZW4008DV | IC: 6924A-ZW4008DV
Jasco Products Company | Model: ZW4008DV/43072
10 E. Memorial Rd., Oklahoma City, OK 73114 | 1-800-654-8483
CAN ICES-3(B)/NMB-3(B)
All brand names shown are trademarks MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA
of their respective owners.
JASCO PRODUCTS COMPANY LLC,
Tous les noms de marque illustrés sont des marques
10 E. MEMORIAL RD., OKLAHOMA CITY, OK 73114.
de commerce de leurs propriétaires respectifs.
©JASCO 2020 | 43072 | ZW4008DV 09/16/20 v4
Todas las marcas que aparecen aquí son marcas
registradas de sus respectivos dueños.
1. 1.
Tools you will need
IMPORTANT!
The switch is designed only for use with permanently installed fixtures
controlled by the Z-Wave in-wall smart switch must not exceed 960W
(120VAC)/1385W (277VAC) incandescent, 1/2HP (120/277VAC) motor
or 1800W(15A) (120VAC) / 15A (277VAC)
Getting to know your new Z-Wave device
• Turn ON/OFF manually or remotely via the Z-Wave controller
• Can be added in multiple groups and scenes
• May be used in single-pole installation or with up to four add-on
switches (model 46199) in 3-way or 4-way wiring configurations
• Compatible with all incandescent and CFL/LED bulbs
• Auto line/load detection
• Interchangeable paddle switch — white & light almond paddle in package
• Uses a standard, rocker-style wallplate for single-gang installations
(wallplate not included)
• Blue LED indicates switch location in a dark room
• Z-Wave certified for simple pairing and integrated home automation
• Screw terminal installation — requires wiring connections for line (hot),
load, neutral and ground. Traveler wire required for 3-way or 4-way
installation
• This Z-Wave device has advanced features that allow you to customize
your experience. These features can only be adjusted by a Z-Wave enabled
controller that supports the Z-Wave configuration command class. For a
complete list of adjustable configurations, visit www.ezzwave.com/config
2. 2.
A
B D
F
G
C
E
A. Ground (Green/Bare) F. Top rocker — press
to turn switch ON
B. Line or Load (Black)
G. Bottom rocker — press
C. Line or Load (Black)
to turn switch OFF
D. Traveler (Red/Other)
E. Neutral (White)
MANUAL • MANUEL • MANUAL
In-Wall
READ IT OR WATCH IT
Smart Switch
Montage mural
intelligent enfichable
Interruptor Read instructions or watch easy-to-follow video.
de pared
Scan QR code or visit https://byjasco.com/43072i
inteligente
Convert any smart control* to a multi-location switch
*For a list of compatible devices, visit ezzwave.com
Smart control Add-on switches
To purchase an add-on switch or for more details,
visit ezaddonswitch.com.
Multiple paddle
colors available
ezzwave.com/paddlecolors
Purchase additional items at
EZzwave.com or visit your local retailer.
In-Wall Plug-in
Smart Dimmers Smart Dimmers Add-on Switches
In-Wall Motion Plug-in
Switch or Dimmer Smart Switches Smart Switches
Enbrighten In-Wall
Smart LED Bulb Smart Fan Control Smart Door Sensor
In-Wall
Direct Wire, Portable
40A Outdoor Smart Multi Tamper-Resistant
Smart Switch Sensor Smart Outlet
3. 3.
OR
OR
WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the switch and lighting fixture
at the service panel. All wiring connections must be made with the POWER
OFF to avoid personal injury and/or damage to the switch. This device is
intended for installation in accordance with the National Electric Code and
local regulations in the United States or the Canadian Electrical Code and local
regulations in Canada. If you are unsure or uncomfortable about performing
this installation, consult a qualified electrician.
Multi-switch wiring
l
For 3-way installations, please refer to add-on switch (46199) manua
Single-switch wiring
Before installation, you may wish to change the paddle color to match your wallplate
or décor. Please proceed to section 5.
1. Shut off power to the circuit at circuit breaker or fuse box.
IMPORTANT! Verify power is OFF to switch box before continuing.
2. Remove wallplate.
3. Remove the switch mounting screws.
4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.
5. There are up to five screw terminals on the switch; these are marked:
A. GROUND — Green/Bare
B. LINE OR LOAD — Black (connected to power or lighting)
4. 4.
Adding your device to a Z-Wave network To remove and reset the device
1. Follow the instructions for your Z-Wave certified
1. Follow the instructions for your Z-Wave certified controller
controller to add a device to the Z-Wave network.
to remove a device from the Z-Wave network.
2. Once the controller is ready to add your device, press the
2. Once the controller is ready to remove your device, press
top or bottom of the wireless smart switch (rocker).
the top or bottom of the wireless smart switch (rocker).
You have complete control to turn your fixture ON/OFF according
To return your switch to factory defaults
to groups, scenes, schedules and interactive automations
programmed by your controller. If your Z-Wave
1. Quickly press ON (top) button three times, then
certified controller features remote access, you can control
immediately press the OFF (bottom) button three times.
your fixture from your mobile devices.
The LED will flash ON/OFF five times when completed
successfully.
If prompted by the controller to enter the S2 security code,
refer to the QR code/security number on the side of the box
Note: This should only be used if your network's primary
or the QR code label on the product (see Figure 1). Enter
controller is missing or otherwise inoperable.
the 5-digit code.
NOTE: SmartStart enabled products can be added into a
Z-Wave network by scanning the QR code on the product with
Figure 1:
a controller providing SmartStart inclusion. No further action is
required and the SmartStart product will be added automatically
within 10 minutes of being switched on in the network vicinity.
DO NOT RETURN THIS
PRODUCT TO THE STORE
STOP
NE RETOURNEZ PAS
CE PRODUIT AU MAGASIN
NO DEVUELVA ESTE
PRODUCTO A LA TIENDA
If you have any problems or questions, contact our U.S.-based Consumer Care at
1-800-654-8483, option 1, Monday–Friday, 7AM–8PM Central Time.
For the most up-to-date product support, accessories, electronic
(PDF) format manuals and more, visit www.byjasco.com/support.
• No user-serviceable parts in this unit.
Si vous avez des problèmes ou des questions, veuillez communiquer avec notre
service à la clientèle aux États-Unis au 1-800-654-8483, option 1, du lundi au
43072
vendredi, de 7 h à 20 h (HNC).
ZW4008DV
Pour le soutien relatif aux produits le plus à jour, les accessoires, les manuels en
format électronique (PDF) et plus encore, visitez le site www.byjasco.com/support.
• Aucune des pièces de ce dispositif ne peut être réparée par l'utilisateur.
Si tiene problemas o dudas, comuníquese con nuestro Centro de
atención al cliente con sede en EE. UU. al 1-800-654-8483, opción 1 de
lunes a viernes, de 7 a.m. a 8 p.m., hora estándar del centro (CST).
Para recibir el soporte técnico más actualizado sobre productos, accesorios,
manuales en formato digital (PDF), entre otros, visite www.byjasco.com/support.
• Esta unidad no contiene piezas que el usuario pueda reparar.
WARNING
RISK OF FIRE RIESGO DE INCENDIO
RISK OF ELECTRICAL SHOCK RIESGO DE DESCARGA ELÉCTRICA
RISK OF BURNS
RIESGO DE QUEMADURAS
CONTROLLING APPLIANCES
CONTROL DE EQUIPOS
CAUTION:
ELECTRODOMÉSTICOS
• DO NOT EXCEED RATINGS
PRECAUCIÓN:
• DO NOT USE TO CONTROL ANY DEVICE
• USAR EXCLUSIVAMENTE PARA
WHERE UNINTENDED OPERATION
CONTROLAR BOMBILLAS CFL/LED
COULD CAUSE UNSAFE CONDITIONS
INCANDESCENTES O ATENUABLES
(HEAT LAMP, SUN LAMP, ETC.)
• NO SUPERE LOS VALORES
• DO NOT USE TO CONTROL RECEPTACLES
NOMINALES ELÉCTRICOS
• FOR INDOOR USE ONLY
• NO USAR PARA CONTROLAR DISPOSITIVOS
EN LOS QUE EL FUNCIONAMIENTO NO
AVERTISSEMENT
INTENCIONADO PODRÍA PROVOCAR
SITUACIONES PELIGROSAS (LÁMPARAS DE
RISQUE D'INCENDIE CALEFACCIÓN, LÁMPARAS SOLARES, ETC.)
RISQUE DE CHOC ÉLECTRIQUE
• NO UTILICE PARA CONTROLAR
RISQUE DE BRÛLURES TOMACORRIENTES
• USE SOLAMENTE EN INTERIORES
COMMANDE DES APPAREILS
NOT FOR USE WITH MEDICAL OR
ATTENTION:
LIFE-SUPPORT EQUIPMENT
• UTILISER SEULEMENT POUR COMMANDER
Z-WAVE ENABLED DEVICES SHOULD
LES AMPOULES À DEL ET FLUOCOMPACTES À
NEVER BE USED TO SUPPLY POWER TO
INCANDESCENCE OU À INTENSITÉ RÉGLABLE
OR CONTROL THE ON/OFF STATUS OF
• NE PAS DÉPASSER LES
MEDICAL OR LIFE-SUPPORT EQUIPMENT.
CARACTÉRISTIQUES NOMINALES
• NE PAS UTILISER POUR COMMANDER
NE PAS UTILISER AVEC UN ÉQUIPEMENT
DES APPAREILS POUR LESQUELS
MÉDICAL OU DE SURVIE
UN FONCTIONNEMENT IMPRÉVU
LES DISPOSITIFS COMPATIBLES AVEC LA
POURRAIT ENTRAÎNER DES CONDITIONS
DANGEREUSES (LAMPE À RAYONS TECHNOLOGIE Z-WAVE NE DEVRAIENT
JAMAIS ÊTRE UTILISÉS POUR ALIMENTER OU
INFRAROUGES, LAMPE SOLAIRE, ETC.)
COMMANDER LA MISE EN MARCHE OU L'ARRÊT
• NE PAS UTILISER POUR COMMANDER
DE L'ÉQUIPEMENT MÉDICAL OU DE SURVIE
LES PRISES DE COURANT
• POUR UTILISATION INTÉRIEURE UNIQUEMENT
SE PROHÍBE SU EMPLEO EN
In-Wall EQUIPO MÉDICO O EQUIPO
PARA EL MANTENIMIENTO DE
LAS FUNCIONES VITALES
LOS DISPOSITIVOS Z-WAVE NUNCA SE
DEBEN USAR PARA SUMINISTRAR ENERGÍA
ELÉCTRICA AL EQUIPO MÉDICO O AL EQUIPO
PARA EL MANTENIMIENTO DE FUNCIONES
VITALES, NI PARA CONTROLAR EL ESTADO DE
ENCENDIDO O APAGADO DE DICHOS EQUIPOS.
In-Wall
Hinge Pin
Plug-in
Outdoor Smart
Switch
Insert wires into holes, do not wrap wires
Out to Light (Load)
around screws.
Do not remove screws.
B
D
E
A
C
From Breaker Box
C. LINE OR LOAD — Black (connected to power or lighting)
D. TRAVELER — Red/Other (only in 3-way installations)
E. NEUTRAL — White
Match these screw terminals to the wires connected to the existing switch.
6. Disconnect the wires from the existing switch. Label wires according to
the previous terminal connection.
Observe important wiring information
IMPORTANT! This switch is rated for and intended
to only be used with copper wire.
Wire gauge requirements
Use 14AWG or larger wires suitable for at least 80° C for supplying
line (hot), load, neutral, ground and traveler connections.
Wire strip length:
1. F
or attachment using the enclosure's holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 14Kgf-cm (12lbf-in).
2. Connect the green or bare copper ground wire to the GROUND terminal.
3. Connect the black wire from the light to either LINE/LOAD terminal.
4. Connect the black wire from the electrical service panel (hot) to the other LINE/LOAD
terminal.
5. Connect the white wire to the NEUTRAL terminal (use a jumper wire if needed).
Note: The traveler terminal is only used for 3-way or 4-way wiring and should remain
unused if the switch is being installed in a 2-way system (one switch & one load).
5. 5.
Z-WAVE INTEROPERABILITY
This product can be included and operated
in any Z-Wave network with other Z-Wave
certified devices from other manufacturers
and/or other applications. All non-battery
DSK :
XXXXX
operated nodes within the network will
-25651-22671
act as repeaters regardless of vendor to
-26939-47599
-19612-25872
DSK/PIN CODE increase reliability of the network.
-47752
WARRANTY
Jasco Products Company warrants this product to be free from manufacturing defects for five years from
the original date of consumer purchase. This warranty is limited to the repair or replacement of this
product only and does not extend to consequential or incidental damage to other products that may be
used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states
do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damage, so the above limitations may not apply to you. This warranty gives
you specific rights, and you may also have other rights which vary from state to state. Please contact our
U.S.-based Consumer Care at 1-800-654-8483 (option 1) between 7AM – 8PM, M-F, Central Time or
www.byjasco.com if the unit should prove defective within the warranty period.
GARANTIE
Jasco Products Company garantit que ce produit est exempt de tout défaut de fabrication pendant une
durée à cinq ans compter de la date de l'achat original par l'acheteur. Cette garantie se limite
exclusivement à la réparation ou au remplacement de ce produit et n'est pas applicable aux dommages
indirects ou accessoires survenus sur d'autres produits utilisés avec ce produit. Cette garantie se substitue
à toute autre garantie expresse ou implicite. Certains États ne permettent pas de restrictions quant à la
durée d'une garantie implicite ou permettent l'exclusion ou la limitation des dommages indirects et
accessoires; il se peut, par conséquent, que cette garantie ne s'applique pas dans votre cas. Cette garantie
vous confère des droits juridiques précis; vous pouvez jouir d'autres droits qui peuvent varier d'un État à
l'autre. Veuillez communiquer avec notre service à la clientèle aux États-Unis au 1-800-654-8483 (option
1) entre 7 h et 20 h, heure du Centre ou par l'intermédiaire de notre site web www.byjasco.com si l'appareil
s'avère défaillant au cours de la période de garantie.
GARANTÍA
Jasco Products Company garantiza que este producto no tendrá defectos de fabricación por un cinco
años a partir de la fecha de compr a del consumidor original. Esta garantía se limita a la reparación o
reposición de este producto y no cubre daños indirectos o incidentales a otros productos que se pudieran
utilizar con este producto. Esta garantía reemplaza cualquier otra garantía explícita o implícita. Algunos
estados no permiten la aplicación de limitaciones respecto de la duración de una garantía implícita o
permiten la exclusión o limitación de la cláusula sobre daños indirectos o incidentales, por este motivo las
limitaciones arriba mencionadas pueden no aplicarse en su caso. Esta garantía le otorga derechos
específicos y es posible que tenga otros derechos que pueden variar según el estado en el que vive. Por
favor, comuníquese con nuestro Centro de atención al cliente con sede en EE. UU. al 1-800-654-8483
(opción 1) entre 7 y 20 h, Hora del Centro, o a través de nuestro sitio de internet www.byjasco.com.
Jasco Products Company LLC, Building B
10 E. Memorial Rd. Oklahoma City, OK 73114.
ADVERTENCIA
SPECIFICATIONS
ZW4008DV
Power: 120/277VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 1800W(15A) (120VAC) / 15A (277VAC)
Range: Up to 150ft. line of sight between the wireless controller and the closest Z-Wave receiver module
Operating temperature range: 32-104° F (0-40° C)
Independently mounted (vertical position only), operating control: type 1.c action, pollution degree (2), impulse
voltage (4000V), software class A
For indoor use only
Specifications subject to change without notice due to continuing product improvement
SPÉCIFICATIONS
ZW4008DV
Tension: 120/277VCA, 60Hz
Signal (fréquence): 908.4/916MHz
Charges maximales: 1800W(15A) (120VAC) / 15A (277VAC)
Portée : Distance à vue entre la télécommande et le module de réception Z-Wave le plus proche allant jusqu'à
150 pi (45.7m).
Plage de températures de fonctionnement : De 0 à 40° C (de 32 à 104° F)
Monté indépendamment (position verticale seulement), intervention de type 1.c commande de fonctionnement,
degré de pollution (2), tension de choc de (4000V), logiciel de classe A
Utilisation intérieure uniquement
En raison d'améliorations continues du produit, les spécifications peuvent faire l'objet de changements sans
préavis
ESPECIFICACIONES:
ZW4008DV
Energía: 120/277VCA, 60Hz
Señal (frecuencia): 908.4/916MHz
Cargas máximas: 1800W(15A) (120VAC) / 15A (277VAC)
Alcance: Hasta 150 pies (45.7m) en línea de visibilidad directa entre el control inalámbrico y el módulo receptor
Z-Wave más cercano
Rango de temperatura de funcionamiento: 0-40° C (32-104° F)
Independientemente montado (solo en posición vertical), control de operación: acción tipo 1.c, grado de contami-
nación (2), voltaje de impulso (4000V), software de clase A
Para uso en espacios interiores solamente
Especificaciones sujetas a cambio sin aviso debido a continuas mejoras del producto
.
Out to Light (Load)
B
A
D
E
C
From Breaker Box
6. Insert switch into the switch box being careful not to pinch or crush wires.
7. Switch must be independently mounted (vertical position only).
8. Secure the switch to the box using the supplied screws.
9. Mount the wallplate.
10. Reapply power to the circuit at fuse box or circuit breaker and test the system.
Basic operation
The connected light can be turned ON/OFF in two ways:
1. Manually from the front panel of the switch.
2. Remotely with a Z-Wave controller.
Manual control
The front panel rocker switch allows the user to turn ON/OFF the connected fixture.
1. To turn the connected fixture ON, press the top of the rocker.
2. To turn the connected fixture OFF, press the bottom of the rocker.
Cycle LED light
The LED below the switch acts as a guide light or status indicator.
How to cycle through options: Press up three times and down once quickly.
1. LED is ON when the load is OFF (guide light in the dark) (default).
2. LED is ON when the load is ON (indicates the switch is ON).
3. LED is always OFF.
4. LED is always ON (illuminates switch in the dark).
To change color of the paddle
2.
This step is optional. Before installation,
you may want to change the color of the
paddle to match your wallplate or décor.
1. Lift the air gap tab at the base of the paddle.
2. Push side tabs in on one side and then the other
to release paddle. Lift the cover up and off.
3. Simply put the new paddle onto the
switch by inserting the air gap and side
tabs and snapping securely into place.
1.
Once this step has been completed, please return
to section 3.
This device supports association command class (3 Groups)
• Association Group 1 supports Lifeline, Binary Switch Report
• Association Group 2 supports Basic Set and is controlled by pressing the ON or
OFF button with the local load
• Association Group 3 supports Basic Set and is controlled by double pressing the
ON or OFF button
• Each Association Group supports 5 total nodes
The add-on switch (46199) is required for
multi-switch 3-way or 4-way installations.
Connecting the traveler terminal of this
switch to a standard switch will cause
damage or result in improper function.
If this switch is a part of a 3-way or
4-way multi-switch installation, do
not connect the traveler wire or apply
power until add-on switch are correctly
installed. For more information on
3-way or 4-way installations, view
the manual or quick-start guide
with the add-on switch (46199).