Weed Eater WE7B Manual De Instrucciones página 5

a WARNING: GFCI protection should be provided
on all circuits or outlets to be used for the power
tool. Receptacles are available having built-in
GFCI protection and should be used for this
measure of protection.
NOTE: Double insulation does not take the place of
normal safety precautions when operating the power
tool.
Before plugging in the power tool, make sure that the
outlet voltage supplied is within the voltage marked on the
power tool's data plate. Do not use "AC only" rated power
tools with a DC power supply.
To reduce the risk of electric shock, use the power tool
only with an extension cord intended for outdoor use, such
as an extension cord of cord type: SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A. or SJTOW-A.
When using an extension cord, be sure to use one heavy
enough to carry the current that your power tool will draw.
An undersized extension cord will cause a drop in line
voltage resulting in loss of power and overheating. The
table below shows the correct size to use depending on
cord length and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
a WARNING! Do not connect the power tool to the
power supply before it is completely assembled.
ATTACHING THE BLOWER TUBE (A)
1. Align the grooves on the blower tube (1) with the
grooves on the blower outlet (2).
2. Push the blower tube onto the blower outlet until it
snaps into place. The blower tube is secured by the
tube release button (3).
To remove the blower tube, press the tube release button
while pulling on the blower tube.
BEFORE STARTING
• Make sure you have the proper personal protective
equipment.
• Inspect the cleanliness of the power tool. Make sure the
handles are dry, clean, and free of oil and grease.
• Inspect for broken or damaged parts. Do not use the
power tool if any damage affects safety or operation.
Have damage repaired by an authorized service center.
• Inspect the extension cord. Replace it if it is damaged.
• Connect the extension cord to the power supply.
Keep the extension cord clear of the work area. Position
the cord so that it will not get caught on bushes, hedges,
tree trunks or other obstructions while you are working.
a WARNING: Check the extension cord before each
use and frequently while working. If damaged,
replace immediately. Never use the tool with a
damaged cord since touching the damaged area
could cause electrical shock, resulting in serious
injury.
STARTING AND STOPPING THE TOOL
Move the ON/OFF switch to the ON (I) position to turn on
the tool.
Move the ON/OFF switch to the OFF (0) position to turn
off the tool.
Minimum gauge for extension cords
Volts
120V
VIBRATION EXPOSURE
Exposure to vibrations through prolonged use of power
tools could cause blood vessel or nerve damage in the
fingers, hands, and joints of people prone to circulation
disorders or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in skin color or
texture, or loss of feeling in the fingers, hands, or joints,
discontinue the use of this power tool and seek medical
attention. An anti-vibration system does not guarantee
the avoidance of these problems. Users who operate
power tools on a continual and regular basis must closely
monitor their physical condition and the condition of the
power tool.
ASSEMBLY
CORD RESTRAINT (B)
1. Make a loop in the extension cord and push the loop
through the slot in the handle.
2. Position the loop over the hook (1) and pull the cord
back through the slot.
3. Insert the receptacle (2) of the extension cord into the
recessed plug (3).
OPERATION
USING THE BLOWER (C)
a WARNING
• The use of eye protection is recommended.
• Inspect the area before using the unit. Remove all
debris and hard objects such as rocks, glass, wire,
etc., that can ricochet, be thrown, or otherwise
cause injury or damage during operation.
• Unplug the power tool from the power source
before making adjustments.
Use your unit as a blower for:
• Sweeping debris or grass clippings from driveways,
sidewalks, patios, etc.
• Blowing grass clippings, straw, or leaves into piles,
or removing debris from corners, around joints, or
between bricks.
Direct air flow by directing the blower tube down or to one
side. Always work away from solid objects such as walks,
large stones, vehicles, and fences.
Clean corners by starting in corners and moving outward.
This will help prevent an accumulation of debris which
could fly into your face.
Be careful when working near plants. The force of the air
could damage tender plants.
Total length of cord
7.6 m 15.2 m 30.4 m
(25 ft) (50 ft) (100 ft)
AWG
18 16 16
45.7 m
(150 ft)
12
5