Technical Data - Skil 1300 Manual Original

a
Mitre saw stand
INTRODUCTION
This mitre saw stand is intended exclusively for mounting
•
mitre saws
• This tool is not intended for professional use
• Check whether the packaging contains all parts as
illustrated in drawing 2
• When parts are missing or damaged, please contact your
dealer
• Read this instruction manual carefully before use and
save it for future reference 3

TECHNICAL DATA

Length (without extension):
Max. length:
Working height:
Max. capacity:
(mitre saw + workpiece)
Weight:
TOOL ELEMENTS 1
A Tool mount brackets
B Knobs for locking extension bars
C Extension bars
D Workpiece support / length stop
E Locking knob
F Unlocking lever (leg)
G Leg
H Wheel
J Quick clamp lever (tool mount)
K Mitre saw mounting set
L C-clip
M Wheel holder
N Tool mount adjustment nut
P Tool mount adjustment screw
SAFETY
WARNING Read all warnings, instructions,
-
illustrations and specifications provided with the mitre
saw stand and the mitre saw to be mounted. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAW STANDS
• Do not modify the mitre saw stand or use it for any
purpose for which it is not intended.
• This stand will accommodate many mitre saws.
However, it should never be used on any mitre saw
with a blade diameter larger than 305 mm. Always
confirm any mitre saw used is mounted securely and
is stable before use. Perform a dry run of the cutting
operation just to make sure that no problems will occur
when the cut is made.
1300
120 cm
203 cm
90 - 101 cm
150 kg
18.5 kg
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Disconnect the plug or remove the battery from the
mitre saw before assembly or making adjustments.
Unintentional switching on of the power tool is the cause
of many accidents.
• Assemble the mitre saw stand in the proper manner
before mounting the power tool. Proper assembly
is important to prevent the risk of a collapse of the saw
stand.
• Attach the mitre saw securely to the saw stand
before using it. Slipping off of the mitre saw on the saw
stand can lead to loss of control.
• Place the mitre saw stand on a dry, stable and flat
surface. If the mitre saw stand can slip off or wobbles,
the mitre saw or the workpiece cannot be uniformly and
securely guided.
• Do not overload the mitre saw stand and do not use
it as a ladder or scaffolding. Overloading or standing
on the mitre saw stand can lead to tipping over.
• When working or transporting, take care that all
bolts and connecting elements are firmly tightened.
Loose connections can lead to instability and inexact
sawing.
• (Dis)mount the mitre saw only when it is in the
transport position (for instructions on the transport
position, also see the operating instructions of the
mitre saw).
• When the mitre saw is mounted to the tool mount
brackets, operate it exclusively on the mitre saw
stand. Without the mitre saw stand, the mitre saw with
tool mount brackets can tip over.
• Ensure that long and heavy workpieces do not
affect the balance of the mitre saw stand. Long and/
or heavy workpieces must be supported at the free end.
USE
• Assembly
- lay down the frame with the folded legs on top and
unlock all 4 legs 4
! make sure that the legs click into the correct
position
- place the saw stand in an upright position on a flat
surface
! make sure that the saw stand is stable, you may
push the legs outwards to enhance stability
- assemble both wheels H to the wheel holder M and to
the frame as shown 5
- assemble workpiece supports D and locking knobs E
as shown 6 a
- assemble knobs for locking the extensions bars B as
shown 6 b
• Mounting the mitre saw to the tool mount brackets 7
! disconnect the plug or remove the battery
from the mitre saw before assembly or making
adjustments
- a standard mitre saw (with mounting holes in a
rectangular pattern) can be mounted directly to the tool
mount brackets A as shown 7 a
- a non-standard mitre saw (with mounting holes in a
trapezoid pattern) can only be mounted to the tool
mount brackets A by using at least 18 mm thick
plywood as shown 7 b
! make sure the tool mount brackets are parallel to
each other
5