Publicidad
IMPORTANT SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the con-
tainers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet
and create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition
should be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means
of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the Fan
when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug™ on your AirKing fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed
or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper
with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no
circumstances should the grounding prong be cut off the plug. Where a two-prong wall receptacle is encountered, it must be
replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and
all applicable local codes and ordinances. This work must be done only by a qualified electrician, using copper wire only.
DO NOT USE A THREE-PRONG TO TWO-PRONG ADAPTER. IMPROPER CONNECTION MAY CREATE THE RISK OF ELEC-
TRICAL SHOCK. USE OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these
devices may overheat and cause a fire hazard.
•DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a fire hazard.
•ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
•NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
•DO NOT block, cover or obstruct air flow to or from the fan while in operation.
•DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location
may create a shock hazard.
•DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
•NEVER use a single extension cord to operate more than one Fan or other electrical device.
•DO NOT use this Fan if it has been damaged or is not functioning properly.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
•THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).This Fan is not suitable for use in hazardous
locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
SAVE THESE INSTRUCTIONS
Rev. Q 4/17
2
ARMADO DEL TUBO
(Figura 1)
1. Saque el tubo de su caja en la forma indicada. (Paso 1)
2. Afloje la Tuerca de Ajuste de Altura haciéndola girar hacia la
izquierda. (Paso 2)
3. Levante el Tubo de Extensión. (Paso 3)
4. Apriete la Tuerca de Ajuste de Altura haciéndola girar hacia la
derecha. (Paso 4)
ARMADO DEL PEDESTAL
COLOQUE LA BASE DE MANERA HORIZONTAL SOBRE
EL PISO
1. Con un movimiento rotatorio, introduzca el extremo del tubo de
diámetro grande dentro del orificio de la Base. El tubo quedará
totalmente asentado en la base su lo hace girar mientras lo empuja.
2. Para Ajustar la Altura:
a.)Afloje la Tuerca de Ajuste de Altura.
b.)Levante o baje el Tubo de Extensión hasta alcanzar
la altura deseada.
c.)Apriete la Tuerca de Ajuste de Altura.
ARMADO DEL CABEZAL
(Figura 3)
1. Coloque el Conjunto del Cabezal con el Collar sobre el Conjunto
de Tubo.
2. Sosteniendo el Tubo de Extensión firmemente, gire el Conjunto
del Cabezal hacia abajo hasta que se asiente sobre el tubo.
PRECAUCIÓN:
Cuando realice el ajuste de la altura después de conectar el
ensamblaje superior, SIEMPRE sostenga el tubo de extensión
con una mano, pues al aflojar la tuerca de ajuste de la altura
puede causar la caída libre del tubo de extensión y el
ensamblaje superior.
ARMADO DE LA HÉLICE Y PARRILLA
1. Incline el Cabezal del Ventilador hacia atrás. Coloque la Parrilla
Trasera en el Motor.
2. Alinee la lengüeta de la Parrilla Posterior de Plástico con la ranura
de la parte superior de la cubierta delantera del Motor. (Figura 4A)
3. Asiente totalmente la Parrilla Trasera y fíjela haciendo girar la
Tuerca Plástica hacia la derecha. Deslice la Hélice sobre el Eje
del Motor (Alinee la ranura del cubo de la hélice con la espiga
del eje del motor).(Figure 4B)
4. Para fijar la Hélice, atornille el Rotador sobre el Eje hacia la
izquierda hasta que quede fijo sobre el cubo de la Hélice.
5. Con el cabezal del motor en posición recta, alinee el Ornamento
de la Parrilla Delantera para que quede horizontal y mirando
hacia arriba. Comenzando con la parte superior de la parrilla y
avanzando hacia abajo, inserte las Trabas de la Parrilla Trasera
a través de las Ranuras de la Parrilla Delantera. (Figura 5).
Figura 1
Tubo de
Extensón
Tuerca de
Ajuste de
Altura
Paso 2
Paso 1
Tuerca de
Ajuste de
Altura
Base
Figura 2
Rev. Q 4/17
2081044
MODELO 4CH63F/9119F
Collar
(Figura 2)
Figura 3
Parrilla
Trasera
Motor
Parrilla
Trasera
(Figura 4)
Ranuras
Ornamento
Figura 5
INCLINACIÓN:
Este Ventilador está
equipado con un Cabezal de Ventila-
dor para ángulos múltiples que per-
Paso 4
mite la Circulación del Aire en Toda la
Paso 3
Habitación. Siga los pasos indicados
a continuación para ajustar correcta-
Tubo de
mente el "ángulo de inclinación" de
Extensión
su Ventilador.
1. Coloque una mano en la barra justo
debajo del Cuello del Ventilador.
2. Coloque la otra mano sobre la parte
superior del Ventilador.
3. Empuje o jale suavemente el ca-
bezal del Ventilador hasta que se
encuentre en la posición deseada.
7
Conjunto de
Cabezal
Tubo de
Extensión
Rotador
Hélice
Tuerca de
Figura 4
Plástico
Motor
Figura 4A
Espiga
Ranura
Figura 4B
Trabas
2081044
Publicidad
